Close Give Feedback
Resene Paints - home page
Follow us on Facebook Follow us on Pinterest Follow us on Instagram Follow us on YouTube

Rose Hughes shows how to build a shady pergola

Our pergola measures 5m x 3.8m, but this project can be scaled to suit your requirements. Before proceeding check with your local council about the applicable building regulations for this project.

You will need: Timber pegs and spare timber for profile and post bracings, about 2 x 25kg bags of instant cement per hole,

Also required: 12 x 10 x 120mm coach bolts and round washers and 4 x 10 x 150mm coach bolts with washers, 2 x 150mm coach screws, 8g x 40mm screws, 8g x 100mm screws, 5 x 52 x 120mm joist hangers, stain (I used Resene Woodsman Wood Oil Stain in Shadow Match), builder’s string, small nail/ pencil/tape, clamps, drop saw, skill saw, handsaw, spirit level , hammer, screwdriver/drill and drill bits.

Cost: $ 2000

Step 1 Step one
Mark out roughly where your pergola is going to sit and set up profiles about 500mm back from the corners. Run string lines from your profiles to give you the outside area of your pergola. The outside corner posts will sit where the string lines meet. I used 4 corner posts and 5 mid posts.
Step 2 Step two
Mark and dig 400mm x 400mm x 600mm deep holes for each post. Mix the cement according to the instructions. One at a time, put a small amount of cement in each hole, add the post, brace well and ensure each post is straight. Pour in the cement and tamp down to remove any air. Allow the cement to dry before removing the bracing.
Step 3 Step three
Measure to the underside of the bearer – I chose 2.2m. Mark the  first post at this height with a nail; use timber and the spirit level to mark the rest. Do the same 130mm above the  first line. Saw off posts at this line. Each corner post and post on the front and back of the pergola will have a 50mm rebate cut into it. Each corner post and side post will have a 30mm rebate. See image 3. Mark and cut with the handsaw.
Step 4 Step four
Measure and cut the bearers. Hold in place with clamps and drill 10mm holes for the coach bolts. For the corner posts, there should be 2 vertical bolt holes for the front and back bearers, and a single hole between for the side bearers. The mid posts should all have 2 vertical holes.
Step 5 Step five
Identify and take down the bearers; stain these and the posts. Once dry, reinstate the bearers and bolt the upper frame together with the coach bolts. The front and back bearers attach with the 120mm coach bolts (apart from the centre front post), and the side bearers with the 150mm coach bolts. The bolts on the back wall should have the heads to the inside.
Step 6 Step six
For the back and side walls, measure the distance between the posts where you want to put the battens. Cut the battens to length, pre-drill and attach using the 40mm screws centered on each post. Use the clamps, spirit level and spacers to ensure the gaps are even and the battens are level.
Step 7 Step seven
For the ceiling, measure the side bearers and cut 50mm x 50mm timber to  t; cut 3 to  fit as rafters and trim the width back to 130mm using the skill saw. Stain all pieces. Attach the side rails with 100mm screws between the posts, level with the rebate, to create a ledge for the ceiling battens. Centre and hang the side rafters with joist hangers so the lower edge is level with the lower edge of the main bearers. For the central rafter, use 150mm coach screws to join post bearer and rafter.
Step 8 Step eight
Cut the ceiling battens to  fit, then pre-drill and screw in place using the spacers, working from the back to the front and attaching at the sides and the centre of each rafter.

View more projects

 

Order online now:
Testpots | Paints | Primers and Sealers | Stains | Clears | Accessories

Get inspired Get inspired ! Subscribe      Get saving Get saving ! Apply for a DIY card

Resene Paints Ltd

Can't find what you're looking for? Ask us!

Resene Paints (Australia) Limited   – www.resene.com

Follow us on Facebook Follow us on Pinterest Follow us on Instagram Follow us on YouTube
Videos on how to paint and stain your house
 

Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online.   See measurements/conversions for more details on how electronic colour values are achieved.

What's new | Specifiers | Painters | DIYers | Artists | Kids | Sitemap | Home | TOP ⇧