6701R RESENE PAINTING Masterspec sections must be customised to suit the project being specified, by removing irrelevant information and adding project-specific information and selections. 1. GENERAL This section deals with the surface preparation, painting and clear finishing of new and existing substrates using Resene architectural and decorative coating systems; and with the supply and application of paper-backed wallpaper. Modify or extend the above description to suit the project being specified. For specific technical information call the Resene Technical Helpline 0800 RESENE (0800 737 363) or at www.resene.co.nz. This painting specification is written based on information available at the time of writing. This painting specification assumes that the applicator has the necessary skill, experience and equipment to undertake the work. The applicator remains responsible for ensuring proper completion of the work. If in the applicator’s own expertise and judgement an amendment to this specification is required, or where a substrate preparation, or required painting system is not covered in this specification, this shall be brought to the attention of the principal and any amendment agreed before work proceeds any further. This section has been written for use with Resene One-Line specifications and product data manual. Modify and extend the selected systems (refer to SELECTIONS) as necessary for the substrate and its particular location (e.g. The substrate may be the same for bathroom and bedroom but the finish may differ). Refer to the Resene One-Line specifications and product data manual for a comprehensive listing of Resene One-Line specification systems. Include the Resene One-Line specifications in any finishes/colour schemes prepared for the project. Add project-specific clauses where extensive masking and spraying of coatings is involved; especially where solventborne products are specified. Add clauses when specifying spray or roller-applied high-build products, or when specifying heavy-duty and solid vinyl wallcoverings. 1.1 DOCUMENTS REFERRED TO Documents referred to in this section are: Health and Safety in Employment Act 1992 MPNZA Specification manual Documents listed above and cited in the clauses that follow are part of this specification. However, this specification takes precedence in the event of it being at variance with the cited document. Delete from the DOCUMENTS clause any document not cited. List any additional cited documents. RELATED DOCUMENTS Refer to the following related documents when preparing this section: NZBC C3/AS1 Spread of fire 8.0 Surface finishes, floor coverings and suspended flexible fabrics NZBC F2 Hazardous building materials AS/NZS 2312 Guide to the protection of structural steel against exterior atmospheric corrosion by the use of protective coatings AS/NZS 2311 Guide to the painting of buildings Dangerous Goods Regulations, Flammable Liquids 1985 OSH: Guidelines for the provision of facilities and general safety in the construction industry New Zealand Painting Contractors Association (Inc): Painter’s hazard handbook BRANZ Bulletin 296 Transparent and semi-transparent exterior finishes for timber exposed to the weather BRANZ Bulletin 332 Claddings in corrosive environments 1.2 MANUFACTURER’S DOCUMENTS Manufacturer’s and supplier’s documents relating to work in this section are: Resene One-Line specifications and product data manual (hardcopy or at www.resene.co.nz) Resene Putting your safety first Copies of the above literature are available from Resene Telephone: 0800 RESENE (0800 737 363) It is important to ensure that all personnel on site have access to accurate, up to date technical information on the many products, materials and equipment used on a project. In most cases individual products are not used in isolation, but form part of a building process. Also a particular manufacturer’s and/or supplier’s requirements for handling, storage, preparation, installation, finishing and protection of their product can vary from what might be considered the norm. Access to technical information can help overcome this potential problem. 1.3 ABBREVIATIONS The following abbreviations are used throughout this part of the specification: MPNZA Master Painters New Zealand Association Inc. Refer to the Preliminaries and General for abbreviations used throughout the specification. 1.4 NO SUBSTITUTIONS Substitutions are not permitted to any specified Resene system, or associated components and products. 1.5 PAINTER QUALIFICATION All work to be carried out by persons competent in the trade and experienced with the Resene coating systems and techniques specified. Expand this clause when special skills are needed. 1.6 HEALTH AND SAFETY Refer to and comply with the requirements of the Health and Safety in Employment Act 1992 including the obligation to: - Eliminate hazards and if hazards cannot be eliminated or isolated, then minimise the hazards in this work by using the proper equipment and techniques as required by the MPNZA Painters hazard handbook and Resene Putting your safety first handbook. - Supply protective clothing and equipment. - Inform the contractor as well as the employees and others on site of those hazards and put in place procedures for dealing with emergencies. Use this clause if the coatings being used have a hazard substance base. 1.7 CONTROL SAMPLES Prepare samples of the finished work as scheduled, including preparation and colour as specified. Obtain approval of the appearance before proceeding. Refer to SELECTIONS for location and paint type requirements. Use this clause where appearance is the main criterion. The size and form of samples depend on the nature of the project. 2. PRODUCTS 2.1 PAINT TYPES All paint coatings to be Resene products (which are guaranteed for consistency and performance under ISO 9001) prepared, mixed and applied as directed in the Resene One-Line specifications and product data manual. 2.2 GAP FILLERS Use suitable gap fillers to match the surface being prepared. Any special primers required of the fillers must be satisfied. Refer to Resene surface preparation sheets in the Resene One-Line specifications and product data manual. 3. EXECUTION 3.1 INSPECT Inspect all surfaces to be painted and report any that will not, after the preparation as laid down in the Resene surface preparation sheets; allow work of the required standard. 3.2 PROTECT Cover up all adjoining surfaces and areas liable to damage or over-painting. Modify this clause to more fully describe project conditions. 3.3 REMOVE HARDWARE Remove hardware and door/window furniture and replace on completion. Do not paint over permanently attached hinges, or any hardware items which cannot be removed. Refer to SELECTIONS for requirements. This clause is to prevent over-painting and to ensure a clean, overlapped line between paint and door escutcheons and the like. Expand to cover any special requirements, such as avoiding over-painting on hinges and similar attached hardware, or conversely for doors to be de-mounted for painting on- or off-site. 3.4 PRIMING AND SEALING Ensure that all priming and sealing work necessary before or during construction is carried out when required. 3.5 ENVIRONMENTAL CONDITIONS Carry out work within acceptable temperature and humidity limits, with timber dry, all to the requirements of Resene. Modify this clause to suit likely project conditions. 3.6 SELECTIONS Confirm all selections, colours and finishes for both paint and wallpaper with the owner, before commencing work. 3.7 LEAD-BASED PAINT, ASBESTOS Lead-based paint and asbestos, if present: handle as outlined in the preamble to the Resene One-Line specifications and product data manual. 3.8 SHARP EDGES, CRACKS AND HOLES Sharp edges, cracks and holes if present: remove and/or repair as outlined in the preamble to the Resene One-Line specifications and product data manual. 3.9 PREPARE ALL SURFACES Prepare all surfaces to be coated to the requirements of the Resene surface preparation sheets. Use suitable gap fillers to match the surface being prepared. Any special primers required of the fillers must be satisfied. Refer to Resene surface preparation sheets. 3.10 APPLICATION Apply paint by brush and/or roller to the requirements of Resene to obtain a smooth, even coating of the specified thickness, uniform gloss and colour. Do not spray on site without express permission. Expand and modify this clause to more fully describe project requirements. 3.11 RESENE SPECIFICATIONS Refer to the Resene One-Line Specifications and Product Data Manual for surface preparation, coating sequence and application requirements as they apply to each system. Correct defective work immediately, with any recoating following the system’s requirements. 3.12 SCUFF BETWEEN COATS Between all coats remove any dust pick-up, protruding fibres and coarse particles. 3.13 FINISHED PAINT SURFACES All finished paint surfaces to show uniformity of gloss and colour, to have the correct thickness for each coat, and freedom from painting defects such as tackiness and conspicuous brush marks. Finished work to be clean and free of any disfigurement. 3.14 CONFIRM WALLPAPER Confirm that all rolls of each pattern are from the same batch. 3.15 WALLPAPER INSTALLATION Seal or size walls. Drops to be full-length, completely glued, pattern matched and hung vertically without bubbles or visible butt joints. Scribe cut paper 2 mm onto surrounding trim. Expand this clause to include specific project requirements, or when special papers are being used. 3.16 CLEAN Clean adjoining surfaces, glass and fittings of any paint contamination. 3.17 REPLACE Replace hardware without damage to the hardware or the adjoining surfaces. 3.18 TAKE AWAY Take away from the site unused painting materials and equipment. 4. SELECTIONS 4.1 CONTROL SAMPLES Location / substrate Resene number / system ~ Use this clause where appearance is the main criteria. The size and form of samples depend on the nature of the project. 4.2 HARDWARE FOR REMOVAL Hardware for removal: ~ 4.3 PAINT SYSTEMS, EXTERIOR To the Resene One-Line specifications as listed for the different substrates. Refer to the Resene manual for the first and second coats of each system to suit the particular substrate and condition. Concrete, concrete masonry, tilt slab, GRC, fibre reinforced cement boards, cement render including stucco, rough cast, EIFS. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec1_Cementitious.pdf Description: Exterior cementitious surfaces, waterborne semi-gloss System: Resene One-Line Spec. No. 1e 1.2 Surface prep: D83; and for thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Sonyx 101 D30, waterborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Sonyx 101 D30, waterborne semi-gloss 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) Exterior timbers. For more information: Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Exterior timbers, waterborne gloss System: Resene One-Line Spec. No. 2e 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Hi-Glo D31, waterborne gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Hi-Glo D31, waterborne gloss Exterior timbers, stains and clear finishes. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Exterior timbers, stains and clear finishes, waterborne stain System: Resene One-Line Spec. No. 2e 3.5 Surface prep: D82 1st coat: Resene Waterborne Woodsman D57a, waterborne stain 2nd coat: Resene Waterborne Woodsman D57a, waterborne stain 3rd coat: Resene Waterborne Woodsman D57a, waterborne stain (after 3 months) Exterior timber joinery, including doors and windows. For cedar refer to 8e. For totara and matai refer to 9e. For more information: Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf http://www.resene.co.nz/archspec/datashts/spec3_Timber_Joinery.pdf http://www.resene.co.nz/archspec/datashts/spec8_Cedar_Exterior.pdf http://www.resene.co.nz/archspec/datashts/spec9_Matai_Totara.pdf Description: Exterior timber joinery, waterborne gloss System: Resene One-Line Spec. No. 3e 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer 2nd coat: Resene Lustacryl D310, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne gloss enamel Exterior timber decks, pergolas and fences. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec4_Timber_Decks_Fences.pdf Description: Exterior timber decks, pergolas and fences, waterborne stain System: Resene One-Line Spec. No. 4e 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Lumbersider D34, waterborne satin 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin Exterior galvanised steel and Zincalume. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec5_Steel_Galvanised_Ext.pdf For demanding and aggressive exterior environments, refer to One-Line specifications 22-24 or the Resene Engineered Coating Systems Manual Description: Exterior galvanised steel and Zincalume, waterborne gloss System: Resene One-Line Spec. No. 5e 1.1 Surface prep: D89 1st coat: For new work - Resene Galvo-Prime D402, waterborne galvanised iron primer; or For repaint - Resene Galvo One D41, solventborne galvanised iron primer 2nd coat: Resene Hi-Glo D31, waterborne gloss 3rd coat: Resene Hi-Glo D31, waterborne gloss Exterior cedar. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec8_Cedar_Exterior.pdf Description: Exterior cedar, waterborne satin System: Resene One-Line Spec. No. 8e 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For new cedar - Resene Quick Dry D45 (2 coats), waterborne primer/undercoat; or For weathered cedar - Resene Wood Primer D40, solventborne primer 2nd coat: Resene Lumbersider D34, waterborne satin; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lumbersider D34, waterborne satin Waterproofing membranes. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec17_Waterproofing_Memb.pdf Description: Waterproofing membranes, waterborne low sheen System: Resene One-Line Spec. No. 17e 1.4 Surface prep: D83; and for thin plaster - Resene Limelock D809 cure/seal 1st coat: For risk of mould - Resene Quick Dry D45, waterborne primer/undercoat; or For powdery surfaces - Resene Sureseal D42, solventborne sealer; or Self priming - Resene X-200 D62, waterborne low sheen 2nd coat: Resene X-200 D62, waterborne low sheen 3rd coat: Resene X-200 D62, waterborne low sheen 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) Exterior metallic finishes. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec25_Special_Effects.pdf Description: Exterior waterborne metallic System: Resene One-Line Spec. No. 25e 1.3/5 Surface prep: D83 1st coat: Resene Quick Dry D45, waterborne primer/undercoat 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Enamacryl Metallic D309a, waterborne metallic 4th coat: Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Multishield+ D54a, waterborne glaze (optional) Other Resene exterior systems. For more information: 7e EXTERIOR NON-FERROUS METALS Refer to: http://www.resene.co.nz/archspec/datashts/spec7_Non-Ferrous_Metals.pdf 9e EXTERIOR TOTARA AND MATAI TIMBER, STAINS AND CLEAR FINISHES Refer to: http://www.resene.co.nz/archspec/datashts/spec9_Matai_Totara.pdf 10e EXTERIOR BITUMEN, BUTYL AND EPDM RUBBERS Refer to: http://www.resene.co.nz/archspec/datashts/spec10_Bitumen_Rubbers.pdf 11e EXTERIOR BAKED ENAMEL SYSTEMS (COLORSTEEL®/COLORBOND®), GLASS, GLAZED TILES, POLYETHYLENE AND POLYPROPYLENE Refer to: http://www.resene.co.nz/archspec/datashts/spec11_Enamel_Glass_Tiles.pdf 12e ACRYLIC SHEETING (PERSPEX), GLASS REINFORCED EPOXY, GLASS REINFORCED POLYESTER, POLYCARBONATE, POLYSTYRENE, uPVC Refer to: http://www.resene.co.nz/archspec/datashts/spec12_Plastic_Materials.pdf 13e EXTERIOR BRICK AND TERRACOTTA Refer to: http://www.resene.co.nz/archspec/datashts/spec13_Brick_Terracotta.pdf 14e CLEAR FINISHES ON CLAY TILES, DECORATIVE AGGREGATE FLOORING, HARD FIRED NON -BSORBENT TILES, STONE AND SLATE Refer to: http://www.resene.co.nz/archspec/datashts/spec14_Clay_Tiles_Stone.pdf 16e EXTERIOR CANVAS Refer to: http://www.resene.co.nz/archspec/datashts/spec16_Canvas_Wallpaper.pdf 18e SPECIALIST FLOOR SYSTEMS Refer to: http://www.resene.co.nz/archspec/datashts/spec18_Flooring_Specialist.pdf 19e ANTI-GRAFFITI SYSTEMS Refer to: http://www.resene.co.nz/archspec/datashts/spec19_Anti-Graffiti_System.pdf 20e TEXTURED AND SPECIALIST COATINGS Refer to: http://www.resene.co.nz/archspec/datashts/spec20_Textured_Coatings.pdf 21e SPECIALIST PAINT EFFECTS Refer to: http://www.resene.co.nz/archspec/datashts/spec21_Paint_Effects.pdf 4.4 PAINT SYSTEMS, INTERIOR To the Resene One-Line specifications as listed for the different substrates. Refer to the Resene manual for the first and second coats of each system to suit the particular substrate and condition. Interior cementitious surfaces. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec1_Cementitious.pdf Description: Interior cementitious surfaces, waterborne semi-gloss System: Resene One-Line Spec. No. 1i 1.2 Surface prep: D83; and for thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel Interior timber. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Interior timber, waterborne gloss System: Resene One-Line Spec. No. 2i 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Enamacryl D309, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Enamacryl D309, waterborne gloss enamel Interior timber, stains and clear finishes. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Interior timber, stains and clear finishes, solventborne satin System: Resene One-Line Spec. No. 2i 4.3 Surface prep: D82 1st coat: For stained finish – Resene Waterborne Colorwood D50a, waterborne wood stain; or For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne wood stain clear (optional) 2nd coat: Resene Poly-Flat D52, solventborne flat clear; or For particle and fibreboard - Resene Aquaclear D59, waterborne urethane 3rd coat: Resene Poly-Satin D52, solventborne satin clear 4th coat: Resene Poly-Satin D52, solventborne satin clear Interior timber joinery. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec3_Timber_Joinery.pdf Description: Interior timber joinery, waterborne semi-gloss System: Resene One-Line Spec. No. 3i 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel Interior paperfaced plaster/solid plaster/fibrous plaster. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec15_Plaster_Interior.pdf Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne low sheen System: Resene One-Line Spec. No. 15i 1.4 SC Level 5 Surface prep: D84; D85; D87; and D807 Resene Broadwall Surface Prep & Seal, waterborne surfacer; or D810 Broadwall 3 in 1, waterborne surfacer 1st coat: (optional) For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer For new wet areas – Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel Interior metallic finishes. For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec25_Special_Effects.pdf. Description: Interior metallic finishes, waterborne metallic finish on Anaglypta, Scandatex, etc System: Resene One-Line Spec. No. 25i 1.3/5 Surface prep: D84; D85 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Enamacryl Metallic D309a, waterborne metallic 4th coat: Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional) Other Resene interior systems. For more information: 7i INTERIOR NON-FERROUS METALS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec7_Non-Ferrous_Metals.pdf 9i INTERIOR MATAI. SPOTTED GUM AND TOTARA ONLY Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec9_Matai_Totara.pdf 11i INTERIOR BAKED ENAMEL SYSTEMS, GLASS, GLAZED TILES, LAMINATED SURFACES, POLYETHYLENE, POLYPROPYLENE AND VARNISHED SURFACES Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec11_Enamel_Glass_Tiles.pdf 12i INTERIOR GLASS ACRYLIC SHEETING (PERSPEX), GLASS REINFORCED EPOXY, GLASS REINFORCED POLYESTER,POLYCARBONATE, POLYSTYRENE AND Upvc Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec12_Plastic_Materials.pdf 13i INTERIOR BRICK AND TERRACOTTA, CLEAR FINISHES Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec13_Brick_Terracotta.pdf 14i INTERIOR CLEAR FINISHES ON CLAY TILES, DECORATIVE AGGREGATE FLOORING, HARD FIRED NON-ABSORBENT TILES, STONE AND SLATE Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec14_Clay_Tiles_Stone.pdf 16i INTERIOR CANVAS, HESSIAN, PAPER AND SCANDATEX Refer to Resene website http://www.Resene.co.nz/archspec/datashts/spec16_Canvas_Wallpaper.pdf 18i SPECIALIST FLOORING SYSTEMS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec18_Flooring_Specialist.pdf 19i ANTI-GRAFFITI SYSTEMS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec19_Anti-Graffiti_System.pdf 20i TEXTURED AND SPECIALIST COATINGS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec20_Textured_Coatings.pdf 21i SPECIALIST PAINT EFFECTS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec21_Paint_Effects.pdf 26i SPECIALIST INTERIOR FINISHES: RESENE ARMOURCAT ACID-CATALYSED SYSTEMS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec26_Specialist_Acid_Cat.pdf 4.5 WALLPAPER Room name Space number Wallpaper type Reference number ~ © CIL MasterSpec® BASIC 2006 6701R RESENE PAINTING Page 2 Branded specification review for 6701R_MASTERSPEC_BASIC.DOC Version date 31/08/2007 I have checked this specification thoroughly and have verified its content and technical accuracy. ? It is approved for issue ? It is approved for issue with changes as marked ? Signed:................................................................Date:....................................... © CIL MasterSpec® BASIC 2006 6701R RESENE PAINTING Page 1