6711R RESENE PAINTING Masterspec sections must be customised to suit the project being specified, by removing irrelevant information and adding project-specific information and selections. 1. GENERAL This section relates to the surface preparation, painting and clear finishing of new and existing substrates using Resene architectural and decorative coating systems. Modify or extend the above description to suit the project being specified. For specific technical information call the Resene Technical Helpline 0800 RESENE (0800 737 363) or at www.resene.co.nz. This painting specification is written based on information available at the time of writing. This painting specification assumes that the applicator has the necessary skill, experience and equipment to undertake the work. The applicator remains responsible for ensuring proper completion of the work. If in the applicator’s own expertise and judgement an amendment to this specification is required, or where a substrate preparation, or required painting system is not covered in this specification, this shall be brought to the attention of the principal and any amendment agreed before work proceeds any further. Related work 1.1 RELATED SECTIONS Refer to RESENE PROTECTIVE COATINGS - STEELWORK for protective coatings. Include cross references to other sections where these contain related work. Documents 1.2 DOCUMENTS REFERRED TO Documents referred to in this section are: Health and Safety in Employment Act 1992 MPNZA Specification manual Documents listed above and cited in the clauses that follow are part of this specification. However, this specification takes precedence in the event of it being at variance with the cited document. Delete from the DOCUMENTS clause any document not cited. List any additional cited documents. RELATED DOCUMENTS Refer to the following related documents when preparing this section: NZBC C3/AS1 Spread of fire 8.0 Surface finishes, floor coverings and suspended flexible fabrics NZBC F2 Hazardous building materials AS/NZS 2312 Guide to the protection of structural steel against exterior atmospheric corrosion by the use of protective coatings AS/NZS 2311 Guide to the painting of buildings Dangerous Goods Regulations, Flammable Liquids 1985 OSH: Guidelines for the provision of facilities and general safety in the construction industry New Zealand Painting Contractors Association (Inc): Painter’s hazard handbook BRANZ Bulletin 296 Transparent and semi-transparent exterior finishes for timber exposed to the weather BRANZ Bulletin 332 Claddings in corrosive environments 1.3 MANUFACTURER’S DOCUMENTS Manufacturer’s and supplier’s documents relating to work in this section are: Resene One-Line specifications and product data manual (hard copy or at www.resene.co.nz) Resene Putting your safety first Copies of the above literature are available from Resene Telephone: 0800 RESENE (0800 737 363) It is important to ensure that all personnel on site have access to accurate, up to date technical information on the many products, materials and equipment used on a project. In most cases individual products are not used in isolation, but form part of a building process. Also a particular manufacturer’s and/or supplier’s requirements for handling, storage, preparation, installation, finishing and protection of their product can vary from what might be considered the norm. Access to technical information can help overcome this potential problem. 1.4 ABBREVIATIONS The following abbreviations are used throughout this part of the specification: MPNZA Master Painters New Zealand Association Inc. Refer to the Preliminaries and General for abbreviations used throughout the specification. Requirements 1.5 NO SUBSTITUTIONS Substitutions are not permitted to any specified Resene coating system, or associated components and products. 1.6 QUALIFICATIONS Painters to be experienced competent workers, familiar with the materials and the techniques specified and with the Resene coating systems and be members of the Master Painters New Zealand Association Inc. 1.7 CONTROL SAMPLES Prepare samples of the finished work, including the specified preparation. Refer to SELECTIONS for location and type. Obtain approval in writing of the appearance before proceeding. Use the Resene Architectural Sample Box as a basis of standard where appropriate. Use this clause where appearance is the main criteria. Size and form of samples depend on the nature of the project. 1.8 SUPERVISED CONTROL SAMPLES Prepare samples of the finished work including the specified preparation. Refer to SELECTIONS for location and type. Make arrangements for the full-time supervision of the application of each coat. Obtain written approval before proceeding. Supervised control samples may, after written approval, be used for comparative testing of dry film thicknesses of the complete coating systems. Use this clause where both durability and appearance are important. 1.9 HEALTH AND SAFETY Refer to and comply with the requirements of the Health and Safety in Employment Act 1992 including the obligation to: - Eliminate hazards and if hazards cannot be eliminated or isolated, then minimise the hazards in this work by using the proper equipment and techniques as required by the MPNZA Painters hazard handbook and Resene Putting your safety first handbook. - Supply protective clothing and equipment. - Inform the contractor as well as the employees and others on site of those hazards and put in place procedures for dealing with emergencies. Use this clause if the coatings being used have a hazard substance base. 1.10 MATERIAL SAFETY DATA SHEETS Obtain from Resene (phone 0800 RESENE, or www.resene.co.nz) the material safety data sheet for each product used and comply with the required safety procedures. Keep sheets on site. Warranties 1.11 WARRANTY Warrant this work under normal conditions of use against failure. Materials: According to 1(v) Durability of Paint Systems in the Resene One-Line specifications and product data manual Execution: 3 years Refer to the PRELIMINARIES AND GENERAL section for the required form of warranty agreement and details of when completed warranty must be submitted. Check PRELIMINARIES AND GENERAL for the date of commencement of guarantees; which is normally practical completion of the contract. Refer to the chosen conditions of contract as it may also contain information on warranties/guarantees. Performance 1.12 RESENE INSPECTION Permit representatives of Resene to inspect the work in progress and to take samples of their products from site if requested. Resene will take care when inspecting the work, but does not accept any responsibility for the proper completion of the work before or after such inspection. 1.13 INSPECTION OF THE WORK Inspection of the whole of the work at each of the stages set out in SELECTIONS may be made. Agree on a programme that will facilitate such inspection, including notification when each part and stage of the work is ready for inspection. The level of inspection will depend on the nature of the project and will range from full for large or complex projects, through intermittent for straightforward work, to occasional for initially establishing the standards of execution. 2. PRODUCTS Materials 2.1 MATERIALS GENERALLY Use only Resene products (which are guaranteed for consistency and performance under ISO 9001) prepared, mixed and applied as directed in the Resene One-Line specifications and product data manual. 2.2 THINNERS/ADDITIVES Use only if and when expressly directed by Resene for their particular product in a particular application. Accessories 2.3 ACCESSORIES Contact your local Resene ColorShop, if required, for a full range of accessories and usage advice. 3. EXECUTION Conditions 3.1 EXECUTION To conform to required trade practice, which shall be deemed to include those methods, practices and techniques contained in the Master Painters New Zealand Association Inc. Specification manual. 3.2 TREATED SURFACES Where surfaces have been treated with preservatives or fire retardants, check with the treatment manufacturer that coating materials are compatible with the treatment and do not inhibit its performance. If they are not compatible, obtain instructions before proceeding. 3.3 ANCILLARY SURFACES The descriptions of areas in schedules and elsewhere are of necessity simplified. Coat ancillary exposed surfaces to match similar or adjacent materials or areas, except where a fair-faced natural finish is required or items are completely prefinished. In cases of doubt obtain written instructions before proceeding. 3.4 HARDWARE Do not paint hinges or hardware that cannot be removed. Before commencing work carefully remove hardware, fixtures and fittings, set aside where they cannot be damaged or misplaced and replace on completion. Refer to SELECTIONS for hardware, fixtures and fittings for removal. 3.5 PROTECTION Supply, lay and fix dropsheets, coverings and masking necessary to protect adjoining, fixtures, fittings and spaces from paint drops, spots, spray and damage. Application - preparatory work 3.6 SURFACE PREPARATION Refer to the Resene One-Line specifications and product data manual for surface preparation sheets (or obtain them by phoning 0800 RESENE, or at www.resene.co.nz) listed in the materials systems schedule clauses. Carry out the preparatory work required by them for each of the substrates. 3.7 LEAD-BASED PAINT, ASBESTOS Handle cautiously lead-based paint and asbestos, if present, as outlined in the preamble of the Resene One-Line specifications and product data manual and the Putting your safety first brochure. 3.8 SHARP EDGES, CRACKS AND HOLES Remove and/or repair sharp edges, cracks and holes if present, as outlined in the preamble of the Resene One-Line specifications and product data manual. Elastomeric sealants, if used, should not be painted. The paint film will not match the flexibility of the sealant and may severely limit its effectiveness. 3.9 REMEDIAL WORK If any substrate or surface, that even with the preparation work called for in this section, cannot be brought up to a standard that will allow painting or clear finishing of the required standard then do not proceed until remedial work is carried out. 3.10 GAP FILLING Make good cracks, holes, indented and damaged surfaces. Use suitable gap fillers to match the surface being prepared. Any special priming requirements of the fillers must be satisfied. Allow to dry or set before sanding back level with the surface. Prime or seal timber before using putty. Exterior and wet areas: Use only Portland cement base or water-insoluble organic base gap fillers. 3.11 OFF-SITE WORK Carry out this work under cover in a suitable environment with suitable lighting. Store items, both before and after coating, in a clean, dry area protected from the weather and mechanical damage, properly stacked and spaced to allow air circulation and to prevent sticking. 3.12 PRIMING JOINERY Pre-treat any cut surfaces of preservative treated timber before priming. Ensure L.O.S.P. treated joinery has dried sufficiently to lose solvent odour. Pre-treat bare timber with Resene TimberLock (see Data Sheet D48) to improve the durability of subsequent coats. Liberally coat end grain, allow to soak in and then recoat. 3.13 CONCEALED JOINERY SURFACES Where off-site coatings are specified they must be applied to surfaces including those concealed when incorporated into the building. 3.14 CONCEALED METAL SURFACES Apply primer to suit the coating system to surfaces which will be concealed when incorporated into the building. 3.15 EXTERNAL DOORS Prime or seal and paint bottom edges before hanging. 3.16 BEAD GLAZING Stained, varnished, or painted joinery to have the first two coats, or the primer and one undercoat, applied to rebates and beads before glazing. 3.17 PUTTY FRONTING According to the putty manufacturer's instructions allow putty to set, then prime with Resene Wood Primer (see Data Sheet D40). Fully protect the putty by completing the Resene coating system as soon as it is sufficiently firm. Application - generally 3.18 PAINTING GENERALLY Comply with the Resene One-Line specifications and product data manual data sheets and the additional requirements of this work section. 3.19 MIXING Although generally supplied ready-mixed, thoroughly mix paints. Lift any settled pigment and ensure the paint is homogenous. 3.20 ENVIRONMENT Defer painting of exterior surfaces until weather conditions are favourable - warm dry days without frost or heavy dews. Avoid painting in direct sunlight any surfaces that absorb heat excessively. As far as possible apply paint in the temperature range 15°C to 25°C. If temperatures fall outside the range of 10°C and 35°C do not paint unless paints with the necessary temperature tolerance have been specified. Do not apply solventborne paint if moisture is present on the surface. 3.21 SEQUENCE OF OPERATIONS Painting work to generally follow the following sequences: - Complete surface preparation before commencing painting. - Apply primers, sealers, stains, undercoats, paints and clear coatings in the sequences laid down by Resene. - Allow the full drying time between coats laid down by Resene. - Do not expose primers, undercoats and intermediate coats beyond a few days before applying the next coat. - Finish broad areas before painting trim. - Ensure batch numbers of tins are matched for whole areas. - Internally, paint ceilings before walls and walls before joinery, trim and other items. 3.22 APPLICATION Select brush, roller, or pad and apply coatings to the requirements of Resene to obtain a smooth, even coating of the specified thickness, uniform gloss and colour. 3.23 LIGHTLY SAND Lightly sand primers, sealers, undercoats and intermediate coats to remove dust pick-up, protruding fibres and coarse particles. Complete by removing dust immediately before applying the next coat. 3.24 DEFECTIVE WORK Correct defective work immediately and recoat as required, following precisely the Resene system being applied. 3.25 EACH COAT Each coat of paint and the completed paint system to have the following qualities and properties: - Uniform finish, colour, texture, sheen and hiding power and the proper number of coats applied. - No blemishes such as runs, sags, crinkling, fat edges, entrained paint skins, hairs, dust, bare or starved patches, cracks, brush marks, ladder marks and blistering. - Proper covering of corners, crannies, thin edges, cracks, end grain and other difficult places of application. Completion 3.26 CLEAN Clean adjoining surfaces, glass and fittings of any paint contamination. Clean off glass indicators at the completion of the building works. Clean glass inside and out to a shining finish. 3.27 LEAVE Leave the whole of this work uniform in gloss and colour, of correct thickness, free from painting defects, clean and unmarked and to the standard required by following procedures. 3.28 REMOVE Remove dropsheets, coverings and masking to leave surrounding surfaces and areas clean, tidy and undamaged. Remove debris, unused materials and elements from the site. 3.29 REPLACE Replace hardware without damage to it or the adjoining surface and leave hardware properly fitted and in working order. 4. SELECTIONS 4.1 CONTROL SAMPLES Location / substrate Resene One-Line Spec number /system ~ Use this clause where appearance is the main criteria. The size and form of samples depend on the nature of the project. 4.2 SUPERVISED CONTROL SAMPLES Location / substrate Resene One-Line Spec number /system ~ Use this clause where both durability and appearance are important. 4.3 INSPECTION OF WORK Stage Resene One-Line Spec number /system ~ The level of inspection will depend on the nature of the project and will range from full for large or complex projects, through to intermittent for straightforward work, to occasional for initially establishing the standards of execution. 4.4 HARDWARE Hardware for removal: ~ Paint system schedules These suggested schedules may be included here. However they may also be part of a finishes schedule located elsewhere in the specification, may be included on the drawings, or even documented separately. 4.5 EXTERIOR FINISHES Substrate Resene Spec number Colour Weatherboards ~ Timber Joinery/Fascias/Barges ~ Timber Deck ~ Concrete Masonry ~ Dark colours may cause warping on unstable substrates. 4.6 INTERIOR FINISHES Room name Ref Substrate RESENE Spec number Colour Living G02 Ceiling - Plasterboard ~ Exposed Rafters ~ Walls - Plasterboard ~ Trim - Timber ~ Doors - Paint Finish ~ Dining G03 Ceiling - Plasterboard ~ Exposed Rafters ~ Walls - Plasterboard ~ Timber Panelling ~ Trim - Timber ~ Doors - Paint Finish ~ Dark colours may cause warping on unstable substrates. Resene exterior paint systems EXTERIOR PAINT SYSTEMS: Supply the listed Resene systems for the following substrates Note: Select the appropriate first coat by deleting those not applicable: 4.7 EXTERIOR CEMENTITIOUS SURFACES Including concrete, concrete masonry, tilt slab, GRC, fibre reinforced cement boards, cement render including stucco, rough cast, EIFS For more information: Refer to Resene website Refer to http:/www.resene.co.nz/archspec/datashts/spec1_Cementitious.pdf Description: Exterior cementitious surfaces, waterborne gloss System: Resene One-Line Spec. No. 1e 1.1 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Hi-Glo D31, waterborne gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Hi-Glo D31, waterborne gloss 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) Description: Exterior cementitious surfaces, waterborne semi-gloss System: Resene One-Line Spec. No. 1e 1.2 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer Self priming - Resene Sonyx 101 D30, waterborne semi-gloss 2nd coat: Resene Sonyx 101 D30, waterborne semi-gloss 3rd coat: Resene Sonyx 101 D30, waterborne semi-gloss 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) Description: Exterior cementitious surfaces, waterborne satin System: Resene One-Line Spec. No. 1e 1.3 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surface - Resene Sureseal D42, solventborne sealer Self priming - Resene Lumbersider D34, waterborne satin 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) Description: Exterior cementitious surfaces, solventborne gloss System: Resene One-Line Spec. No. 1e 2.1 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss 4.8 EXTERIOR TIMBERS For more information: Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Exterior timbers, waterborne gloss System: Resene One-Line Spec. No. 2e 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Hi-Glo D31, waterborne gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Hi-Glo D31, waterborne gloss Description: Exterior timbers, waterborne semi-gloss System: Resene One-Line Spec. No. 2e 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Sonyx 101 D30, waterborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Sonyx 101 D30, waterborne semi-gloss Description: Exterior timbers, waterborne satin System: Resene One-Line Spec. No. 2e 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only – Resene Sureseal D42, solventborne sealer Self priming – Resene Lumbersider D34, waterborne satin 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin Description: Exterior timbers, solventborne gloss System: Resene One-Line Spec. No. 2e 2.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For hardboard only – Resene Sureseal D42, solventborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss 4.9 EXTERIOR TIMBERS, STAINS AND CLEAR FINISHES For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Exterior timbers, stains and clear finishes, waterborne stain System: Resene One-Line Spec. No. 2e 3.5 Surface prep: D82 1st coat: Resene Waterborne Woodsman D57a, waterborne stain 2nd coat: Resene Waterborne Woodsman D57a, waterborne stain 3rd coat: Resene Waterborne Woodsman D57a, waterborne stain (after 3 months) Description: Exterior timbers, stains and clear finishes, solventborne flat System: Resene One-Line Spec. No. 2e 4.5 Surface prep: D82 1st coat: Resene Woodsman D57, solventborne stain 2nd coat: Resene Woodsman D57, solventborne stain 3rd coat: Resene Woodsman D57, solventborne stain (after 3 months) 4.10 EXTERIOR TIMBER JOINERY Including doors and windows. For cedar refer to 8e. For totara and matai refer to 9e. For more information: Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf http://www.resene.co.nz/archspec/datashts/spec3_Timber_Joinery.pdf http://www.resene.co.nz/archspec/datashts/spec8_Cedar_Exterior.pdf http://www.resene.co.nz/archspec/datashts/spec9_Matai_Totara.pdf Description: Exterior timber joinery, waterborne gloss System: Resene One-Line Spec. No. 3e 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer 2nd coat: Resene Enamacryl D309, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Enamacryl D309, waterborne gloss enamel Description: Exterior timber joinery, waterborne semi-gloss System: Resene One-Line Spec. No. 3e 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system – Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel Description: Exterior timber joinery, solventborne gloss System: Resene One-Line Spec. No. 3e 2.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss 4.11 EXTERIOR TIMBER DECKS, PERGOLAS AND FENCES For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec4_Timber_Decks_Fences.pdf Description: Exterior timber decks, pergolas and fences, waterborne satin System: Resene One-Line Spec. No. 4e 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Lumbersider D34, waterborne satin 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin Description: Exterior timber decks, pergolas and fences, non-skid finish System: Resene One-Line Spec. No. 4e 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: Resene Quick Dry D45, waterborne primer/undercoat 2nd coat: Resene Non-Skid Deck & Path D313, non-skid finish 3rd coat: Resene Non-Skid Deck & Path D313, non-skid finish Description: Exterior timber decks, pergolas and fences, waterborne stain System: Resene One-Line Spec. No. 4e 3.5 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Woodsman D57a, waterborne stain 2nd coat: Resene Waterborne Woodsman D57a, waterborne stain 3rd coat: Resene Waterborne Woodsman D57a, waterborne stain (after 3 months) Description: Exterior timber decks, pergolas and fences, solventborne stain System: Resene One-Line Spec. No. 4e 4.5 Surface prep: D82 1st coat: Resene Woodsman D57, solventborne stain 2nd coat: Resene Woodsman D57, solventborne stain 3rd coat: Resene Woodsman D57, solventborne stain (after 3 months) Description: Exterior timber decks, pergolas and fences, solventborne stain System: Resene One-Line Spec. No. 4.5 C Surface prep: D82 1st coat: Resene Kwila Timber Stain D501, solventborne stain 2nd coat: Resene Kwila Timber Stain D501, solventborne stain Description: Exterior timber decks, pergolas and fences, solventborne oil System: Resene One-Line Spec. No. 4e 4.5 N Surface prep: D82 1st coat: Resene Furniture and Decking Oil D503, solventborne oil 2nd coat: Resene Furniture and Decking Oil D503, solventborne oil 4.12 EXTERIOR GALVANISED STEEL AND ZINCALUME For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec5_Steel_Galvanised_Ext.pdf For demanding and aggressive exterior environments, refer to One-Line Specifications 22-24 or the Resene Engineered Coating Systems Manual. Description: Exterior galvanised steel and Zincalume, waterborne gloss System: Resene One-Line Spec. No. 5e 1.1 Surface prep: D89 1st coat: For new work - Resene Galvo-Prime D402, waterborne galvanised iron primer; or For repaint - Resene Galvo One D41, solventborne galvanised iron primer 2nd coat: Resene Hi-Glo D31, waterborne gloss 3rd coat: Resene Hi-Glo D31, waterborne gloss Description: Exterior galvanised steel and Zincalume, waterborne semi-gloss System: Resene One-Line Spec. No. 5e 1.2 Surface prep: D89 1st coat: For new work - Resene Galvo-Prime D402, waterborne galvanised iron primer; or For repaint - Resene Galvo One D41, solventborne galvanised iron primer 2nd coat: Resene Sonyx 101 D30, waterborne semi-gloss 3rd coat: Resene Sonyx 101 D30, waterborne semi-gloss Description: Exterior galvanised steel and Zincalume, waterborne satin System: Resene One-Line Spec. No. 5e 1.3 Surface prep: D89 1st coat: For new work - Resene Galvo-Prime D402, waterborne galvanised iron primer; or For repaint - Resene Galvo One D41, solventborne galvanised iron primer 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin Description: Exterior galvanised steel and Zincalume, solventborne gloss System: Resene One-Line Spec. No. 5e 2.1 Surface prep: D89 1st coat: Resene Galvo One D41, solventborne galvanised iron primer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss 4.13 EXTERIOR CEDAR For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec8_Cedar_Exterior.pdf Description: Exterior cedar, waterborne gloss System: Resene One-Line Spec. No. 8e 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For new cedar - Resene Quick Dry D45, waterborne primer/undercoat For weathered cedar – Resene Wood Primer D40, solventborne primer 2nd coat: Resene Quick Dry D45, waterborne primer/undercoat 3rd coat: Resene Hi-Glo D31, waterborne gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 4th coat: Resene Hi-Glo D31, waterborne gloss (4th coat optional on weathered cedar) Description: Exterior cedar, waterborne semi-gloss System: Resene One-Line Spec. No. 8e 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For new cedar - Resene Quick Dry D45, waterborne primer/undercoat For weathered cedar – Resene Wood Primer D40, solventborne primer 2nd coat: Resene Quick Dry D45, waterborne primer/undercoat 3rd coat: Resene Sonyx 101 D30, waterborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 4th coat: Resene Sonyx 101 D30, waterborne semi-gloss (4th coat optional on weathered cedar) Description: Exterior cedar, waterborne satin System: Resene One-Line Spec. No. 8e 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For new cedar - Resene Quick Dry D45, waterborne primer/undercoat For weathered cedar – Resene Wood Primer D40, solventborne primer Self priming – Resene Lumbersider D34, waterborne satin 2nd coat: Resene Quick Dry D45, waterborne primer/undercoat 3rd coat: Resene Lumbersider D34, waterborne satin; or Resene Acrylic Undercoat D404, waterborne undercoat 4th coat: Resene Lumbersider D34, waterborne satin (4th coat optional on weathered cedar and not required on self-priming system) Description: Exterior cedar, solventborne gloss System: Resene One-Line Spec. No. 8e 2.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For new cedar - Resene Quick Dry D45, waterborne primer/undercoat For weathered cedar replace 1st and 2nd coat with 1 coat Resene Wood Primer D40, solventborne primer 2nd coat: Resene Quick Dry D45, waterborne primer/undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 4th coat: Resene Super Gloss D32, solventborne gloss Description: Exterior cedar, waterborne stain System: Resene One-Line Spec. No. 8e 3.5 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Woodsman D57a, waterborne stain 2nd coat: Resene Waterborne Woodsman D57a, waterborne stain 3rd coat: Resene Waterborne Woodsman D57a, waterborne stain (after 3 months) Description: Exterior cedar, solventborne stain System: Resene One-Line Spec. No. 8e 4.5 Surface prep: D82 1st coat: For stained finish - Resene Woodsman D57, solventborne stain 2nd coat: Resene Woodsman D57, solventborne stain 3rd coat: Resene Woodsman D57, solventborne stain (after 3 months) Description: Exterior cedar, solventborne stain, kwila timber stain colour System: Resene One-Line Spec. No. 8e 4.5 Surface prep: D82 1st coat: Resene Kwila Timber Stain D501, solventborne stain 2nd coat: Resene Kwila Timber Stain D501, solventborne stain 4.14 WATERPROOFING MEMBRANES For more information: Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec17_Waterproofing_Memb.pdf Description: Barrier membranes, waterborne semi-gloss System: Resene One-Line Spec. No. 17e 1.2T Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces – Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer; or Self priming - Resene Thixalon 5 D63, waterborne semi-gloss 2nd coat: Resene Thixalon 5 D63, waterborne semi-gloss 3rd coat: Resene Thixalon 5 D63, waterborne semi-gloss 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) Description: Waterproofing membranes, waterborne semi-gloss System: Resene One-Line Spec. No. 17e 1.2F Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces – Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer; or Self priming - Resene Flexicover E D64, waterborne semi-gloss 2nd coat: Resene Flexicover E D64, waterborne semi-gloss 3rd coat: Resene Flexicover E D64, waterborne semi-gloss 4th coat: Resene Lumbersider D34, waterborne satin (optional) Description: Waterproofing membranes, waterborne low sheen System: Resene One-Line Spec. No. 17e 1.4 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces – Resene Sureseal D42, solventborne sealer; or Self priming - Resene X-200 D62, waterborne low sheen 2nd coat: Resene X-200 D62, waterborne low sheen 3rd coat: Resene X-200 D62, waterborne low sheen 4th coat: Resene Multishield+ D54a, waterborne glaze (optional) 4.15 EXTERIOR METALLIC FINISHES For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec25_Special_Effects.pdf Description: Exterior waterborne metallic System: Resene One-Line Spec. No. 25e 1.3/5 Surface prep: D83 1st coat: Resene Quick Dry D45, waterborne primer/undercoat 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Enamacryl Metallic D309a, waterborne metallic 4th coat: Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Multishield+ D54a, waterborne glaze (optional) Description: Exterior waterborne pearlescent System: Resene One-Line Spec. No. 25e 1.3/5 P Surface prep: D83 1st coat: Resene Quick Dry D45, waterborne primer/sealer 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin 4th coat: Resene Pearl Shimmer D312, waterborne pearlescent 5th coat: Resene Multishield+ D54a, waterborne glaze (optional) Description: Exterior metallic finish on concrete floor, acrylic urethane System: Resene Spec. No. 25e 2.3/5 Surface prep: D83 1st coat: Resene Armourcote 510 RA40, high solids epoxy 2nd coat: Resene Imperite IF 503 RA81, solventborne metallic 3rd coat: Resene Uracryl 400 Series Clear, acrylic urethane 4.16 OTHER RESENE EXTERIOR SYSTEMS ~ 6e FERROUS METALS Refer to: http://www.resene.co.nz/archspec/datashts/spec6_Ferrous_Metals.pdf 7e EXTERIOR NON-FERROUS METALS Refer to: http://www.resene.co.nz/archspec/datashts/spec7_Non-Ferrous_Metals.pdf 9e EXTERIOR TOTARA AND MATAI TIMBER, STAINS AND CLEAR FINISHES Refer to: http://www.resene.co.nz/archspec/datashts/spec9_Matai_Totara.pdf 10e EXTERIOR BITUMEN, BUTYL AND EPDM RUBBERS Refer to: http://www.resene.co.nz/archspec/datashts/spec10_Bitumen_Rubbers.pdf 11e GLASS, GLAZED TILES, BAKED ENAMEL SYSTEMS Refer to: http://www.resene.co.nz/archspec/datashts/spec11_Enamel_Glass_Tiles.pdf 12e GLASS REINFORCED POLYESTER, EPOXY, PVC, ACRYLIC SHEETING, POLYSTYRENE, POLYCARBONATE Refer to: http://www.resene.co.nz/archspec/datashts/spec12_Plastic_Materials.pdf 13e BRICK AND TERRACOTTA Refer to: http://www.resene.co.nz/archspec/datashts/spec13_Brick_Terracotta.pdf 14e CLEAR FINISHES ON CLAY TILES, ABSORBENT TILES, STONE AND SLATE, DECORATIVE AGGREGATE FLOORING Refer to: http://www.resene.co.nz/archspec/datashts/spec14_Clay_Tiles_Stone.pdf 16e EXTERIOR CANVAS AND AWNINGS Refer to: http://www.resene.co.nz/archspec/datashts/spec16_Canvas_Wallpaper.pdf 18e HEAVY DUTY FLOOR COATINGS Refer to: http://www.resene.co.nz/archspec/datashts/spec18_Flooring_Specialist.pdf 19e ANTI GRAFFITI SYSTEMS Refer to: http://www.resene.co.nz/archspec/datashts/spec19_Anti-Graffiti_System.pdf 20e TEXTURED AND SPECIALIST COATINGS (INCLUDING HARDITEX) Refer to: http://www.resene.co.nz/archspec/datashts/spec20_Textured_Coatings.pdf 21e PAINT EFFECTS Refer to: http://www.resene.co.nz/archspec/datashts/spec21_Paint_Effects.pdf Resene interior paint systems INTERIOR PAINT SYSTEMS: Supply the listed Resene systems for the following substrates (Note: Select the appropriate first coat by deleting those not applicable): 4.17 INTERIOR CEMENTITIOUS SURFACES For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec1_Cementitious.pdf Description: Interior cementitious surfaces, waterborne gloss System: Resene One-Line Spec. No. 1i 1.1 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces – Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Enamacryl D309, waterborne gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Enamacryl D309, waterborne gloss Description: Interior cementitious surfaces, waterborne semi-gloss System: Resene One-Line Spec. No. 1i 1.2 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces – Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer Self priming – Resene Lustacryl D310, waterborne semi-gloss enamel 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel Description: Interior cementitious surfaces, waterborne semi-gloss System: Resene Spec. One-Line No. 1i 1.3 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer Self priming – Resene Lumbersider D34, waterborne satin 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin Description: Interior cementitious surfaces, waterborne low sheen System: Resene One-Line Spec. No. 1i 1.4 ZS Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer Self priming – Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen 2nd coat: Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne satin low sheen 3rd coat: Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen Description: Interior cementitious surfaces, waterborne low sheen enamel System: Resene One-Line Spec. No. 1i 1.4 SC Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer Self priming – Resene SpaceCote Low Sheen D311, waterborne low sheen enamel 2nd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel 3rd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel Description: Interior cementitious surfaces, waterborne flat System: Resene One-Line Spec. No. 1i 1.5 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces – Resene Concrete Primer D405, waterborne primer; or For powdery surfaces – Resene Sureseal D42, solventborne sealer Self priming – Resene Zylone 20 D37, waterborne flat 2nd coat: Resene Zylone 20 D37, waterborne flat 3rd coat: Resene Zylone 20 D37, waterborne flat Description: Interior cementitious surfaces, waterborne flat enamel System: Resene One-Line Spec. No. 1i 1.5 SC Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces – Resene Concrete Primer D405, waterborne primer; or For powdery surfaces – Resene Sureseal D42, solventborne sealer Self priming – Resene SpaceCote Flat D314, waterborne flat enamel 2nd coat: Resene SpaceCote Flat D314, waterborne flat enamel 3rd coat: Resene SpaceCote Flat D314, waterborne flat enamel Description: Interior cementitious surfaces, solventborne gloss System: Resene One-Line Spec. No. 1i 2.1 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces - Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss Description: Interior cementitious surfaces, solventborne semi-gloss System: Resene One-Line Spec. No. 1i 2.2 Surface prep: D83 For thin plaster - Resene Limelock D809, waterborne cure/seal 1st coat: For sound cementitious surfaces, Resene Concrete Primer D405, waterborne primer; or For powdery surfaces - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Lusta-Glo D33, solventborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lusta-Glo D33, solventborne semi-gloss 4.18 INTERIOR TIMBER For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Interior timber, waterborne gloss System: Resene One-Line Spec. No. 2i 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Enamacryl D309, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Enamacryl D309, waterborne gloss enamel Description: Interior timber, waterborne semi-gloss System: Resene One-Line Spec. No. 2i 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel Description: Interior timber, waterborne satin System: Resene One-Line Spec. No. 2i 1.3 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer Self priming - Resene Lumbersider D34, waterborne satin 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin Description: Interior timber, waterborne low sheen System: Resene One-Line Spec. No. 2i 1.4 ZS Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer Self priming - Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen 2nd coat: Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen 3rd coat: Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen Description: Interior timber, waterborne low sheen System: Resene One-Line Spec. No. 2i 1.4 SC Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer Self priming - Resene SpaceCote Low Sheen D311, waterborne low sheen enamel 2nd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel 3rd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel Description: Interior timber, waterborne flat System: Resene One-Line Spec. No. 2i 1.5 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer Self priming - Resene Zylone 20 D37, waterborne flat 2nd coat: Resene Zylone 20 D37, waterborne flat 3rd coat: Resene Zylone 20 D37, waterborne flat Description: Interior timber, waterborne flat System: Resene One-Line Spec. No. 2i 1.5 SC Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer Self priming - Resene SpaceCote Flat D314, waterborne flat enamel 2nd coat: Resene SpaceCote Flat D314, waterborne flat enamel 3rd coat: Resene SpaceCote Flat D314, waterborne flat enamel Description: Interior timber, solventborne gloss System: Resene One-Line Spec. No. 2i 2.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss Description: Interior timber, solventborne semi-gloss System: Resene One-Line Spec. No. 2i 2.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For hardboard only - Resene Sureseal D42, solventborne sealer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lusta-Glo D33, solventborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lusta-Glo D33, solventborne semi-gloss 4.19 INTERIOR TIMBER, STAINS AND CLEAR FINISHES For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Interior timber, stains and clear finishes, waterborne gloss System: Resene One-Line Spec. No. 2i 3.1 Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Aquaclear D59, waterborne gloss urethane 3rd coat: Resene Aquaclear D59, waterborne gloss urethane 4th coat: Resene Aquaclear D59, waterborne gloss urethane 5th coat: Resene Aquaclear D59, waterborne gloss urethane Description: Interior timber, stains and clear finishes, waterborne semi-gloss System: Resene One-Line Spec. No. 2i 3.2 Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Aquaclear D59, waterborne semi-gloss urethane 3rd coat: Resene Aquaclear D59, waterborne semi-gloss urethane 4th coat: Resene Aquaclear D59, waterborne semi-gloss urethane 5th coat: Resene Aquaclear D59, waterborne semi-gloss urethane (optional) Description: Interior timber, stains and clear finishes, waterborne satin System: Resene One-Line Spec. No. 2i 3.3 Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Aquaclear D59, waterborne satin urethane 3rd coat: Resene Aquaclear D59, waterborne satin urethane 4th coat: Resene Aquaclear D59, waterborne satin urethane 5th coat: Resene Aquaclear D59, waterborne satin urethane Description: Interior timber, stains and clear finishes, solventborne gloss System: Resene One-Line Spec. No. 2i 4.1 Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Poly-Flat D52, solventborne flat clear; or For particle and fibre board - Resene Aquaclear D59, waterborne urethane 3rd coat: Resene Poly-Gloss D52, solventborne gloss clear 4th coat: Resene Poly-Gloss D52, solventborne gloss clear Description: Interior timber, stains and clear finishes, heavy duty solventborne gloss System: Resene One-Line Spec. No. 2i 4.1 Surface prep: D82 1st coat: Heavy duty finish - Resene Polythane D53, solventborne gloss clear; For particle and fibre board - Resene Particle Board Sealer D43, waterborne sealer 2nd coat: Resene Polythane, solventborne gloss clear 3rd coat: Resene Polythane, solventborne gloss clear 4th coat: Resene Polythane, solventborne gloss clear Description: Interior timber, stains and clear finishes, solventborne gloss System: Resene One-Line Spec. No. 2i 4.3 Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Poly-Flat D52, solventborne flat clear; or For particle and fibre board - Resene Aquaclear D59, waterborne urethane 3rd coat: Resene Poly-Satin D52, solventborne satin clear 4th coat: Resene Poly-Satin D52, solventborne satin clear Description: Interior timber, stains and clear finishes, solventborne flat System: Resene One-Line Spec. No. 2i 4.5 Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Poly-Flat D52, solventborne flat clear; or For particle and fibre board - Resene Aquaclear D59, waterborne urethane 3rd coat: Resene Poly-Flat D52, solventborne flat clear 4th coat: Resene Poly-Flat D52, solventborne flat clear 4.20 INTERIOR TIMBER FLOORS, STAINS AND CLEAR FINISHES DEDICATED SECTION FOR FLOORS For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec2_Timber_Interior_Ext.pdf Description: Interior timber, stains and clear finishes, waterborne gloss System: Resene One-Line Spec. No. 2i 3.1 F Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Aquaclear D59, waterborne gloss urethane 2nd coat: Resene Aquaclear D59, waterborne gloss urethane 3rd coat: Resene Aquaclear D59, waterborne gloss urethane 4th coat: Resene Aquaclear D59, waterborne gloss urethane 5th coat: Resene Aquaclear D59, waterborne gloss urethane Description: Interior timber, stains and clear finishes, waterborne semi-gloss System: Resene One-Line Spec. No. 2i 3.2 F Surface prep: D82 1st coat: Stained finish – Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Aquaclear D59, waterborne semi-gloss urethane 2nd coat: Resene Aquaclear D59, waterborne semi-gloss urethane 3rd coat: Resene Aquaclear D59, waterborne semi-gloss urethane 4th coat: Resene Aquaclear D59, waterborne semi-gloss urethane 5th coat: Resene Aquaclear D59, waterborne semi-gloss urethane Description: Interior timber, stains and clear finishes, waterborne satin System: Resene One-Line Spec. No. 2i 3.3 F Surface prep: D82 1st coat: Stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or Clear finish - Resene Aquaclear D59, waterborne satin urethane 2nd coat: Resene Aquaclear D59, waterborne satin urethane 3rd coat: Resene Aquaclear D59, waterborne satin urethane 4th coat: Resene Aquaclear D59, waterborne satin urethane 5th coat: Resene Aquaclear D59, waterborne satin urethane Description: Interior timber, stains and clear finishes, solventborne gloss System: Resene One-Line Spec. No. 2i 4.1 F Surface prep: D82 1st coat: For heavy duty finish - Resene Polythane D53, solventborne gloss clear; or For particle and fibre board - Resene Particle Board Sealer D43, waterborne sealer 2nd coat: Resene Polythane D53, solventborne gloss clear 3rd coat: Resene Polythane D53, solventborne gloss clear 4th coat: Resene Polythane D53, solventborne gloss clear Description: Interior timber, stains and clear finishes, solventborne gloss System: Resene One-Line Spec. No. 2i 4.3 F Surface prep: D82 1st coat: For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain 2nd coat: Resene HD Poly-Satin D52, solventborne satin clear; or For particle and fibre board - Resene Aquaclear D59, waterborne urethane 3rd coat: Resene HD Poly-Satin D52, solventborne satin clear 4th coat: Resene HD Poly-Satin D52, solventborne satin clear Description: Interior timber, stains and clear finishes, solventborne gloss System: Resene One-Line Spec. No. 2i 4.3 F Surface prep: D82 1st coat: For clear finish - Resene HD Poly-Satin D52, solventborne satin clear; or For particle and fibre board - Resene Aquaclear D59, waterborne urethane 2nd coat: HD Poly-Satin D52, solventborne satin clear 3rd coat: HD Poly-Satin D52, solventborne satin clear 4th coat: HD Poly-Satin D52, solventborne satin clear 5th coat: HD Poly-Satin D52, solventborne satin clear 4.21 INTERIOR TIMBER JOINERY For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec3_Timber_Joinery.pdf Description: Interior timber joinery, waterborne gloss System: Resene One-Line Spec. No. 3i 1.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45; waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Enamacryl D309, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Enamacryl D309, waterborne gloss enamel Description: Interior timber joinery, waterborne semi-gloss System: Resene One-Line Spec. No. 3i 1.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel Description: Interior timber joinery, waterborne low sheen System: Resene One-Line Spec. No. 3i 1.4 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For painting over varnish – Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel; or Resene Acrylic Undercoat D404 waterborne undercoat 3rd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel Description: Interior timber joinery, waterborne low sheen System: Resene One-Line Spec. No. 3i 1.5 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45, waterborne primer/undercoat; or For timber that stains - Resene Wood Primer D40, solventborne primer; or For painting over varnish – Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene SpaceCote Flat D314, waterborne flat enamel; or Resene Acrylic Undercoat D404 waterborne undercoat 3rd coat: Resene SpaceCote Flat D314, waterborne flat enamel Description: Interior timber joinery, solventborne gloss System: Resene One-Line Spec. No. 3i 2.1 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system - Resene Quick Dry D45; waterborne primer/undercoat; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss Description: Interior timber joinery, solventborne semi-gloss System: Resene One-Line Spec. No. 3i 2.2 Surface prep: D82; and Resene TimberLock D48, solventborne preserver/conditioner 1st coat: For normal recommended system, Resene Quick Dry D45, waterborne primer/undercoat; or For painting over varnish - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lusta-Glo D33, solventborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lusta-Glo D33, solventborne semi-gloss Description: Interior timber joinery, waterborne gloss System: Resene One-Line Spec. No. 3i 3.1 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Aquaclear D59, waterborne gloss urethane 3rd coat: Resene Aquaclear D59, waterborne gloss urethane 4th coat: Resene Aquaclear D59, waterborne gloss urethane 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional) Description: Interior timber joinery, waterborne semi-gloss System: Resene One-Line Spec. No. 3i 3.2 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Aquaclear D59, waterborne semi-gloss urethane 3rd coat: Resene Aquaclear D59, waterborne semi-gloss urethane 4th coat: Resene Aquaclear D59, waterborne semi-gloss urethane 5th coat: Resene Aquaclear D59, waterborne semi-gloss urethane (optional) Description: Interior timber joinery, waterborne satin System: Resene One-Line Spec. No. 3i 3.3 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Aquaclear D59, waterborne satin urethane 3rd coat: Resene Aquaclear D59, waterborne satin urethane 4th coat: Resene Aquaclear D59, waterborne satin urethane 5th coat: Resene Aquaclear D59, waterborne satin urethane (optional) Description: Interior timber joinery, solventborne gloss System: Resene One-Line Spec. No. 3i 4.1 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Waterborne Colorwood D50a, waterborne wood stain 3rd coat: Resene Poly-Flat D52 4th coat: Resene Poly-Gloss D52, solventborne gloss clear 5th coat: Resene Poly-Gloss D52, solventborne gloss clear Description: Interior timber joinery, heavy duty solventborne gloss System: Resene One-Line Spec. No. 3i 4.1 Surface prep: D82 1st coat: For heavy duty finish - Resene Polythane D53, solventborne gloss clear; or For particle and fibreboard - Resene Particle Board Sealer D43, waterborne sealer 2nd coat: Resene Polythane D53, solventborne gloss clear 3rd coat: Resene Polythane D53, solventborne gloss clear 4th coat: Resene Polythane D53, solventborne gloss clear Description: Interior timber joinery, solventborne satin System: Resene One-Line Spec. No. 3i 4.3 Surface prep: D82 1st coat: For stained finish - Resene Waterborne Colorwood D50a, waterborne wood stain; or For clear finish - Resene Waterborne Colorwood Reducing Base D50a, waterborne clear (optional) 2nd coat: Resene Poly-Flat D52, solventborne flat clear 3rd coat: Resene Poly-Satin D52, solventborne satin clear 4th coat: Resene Poly-Satin D52, solventborne satin clear For particle board only, replace 1st coat with Resene Aquaclear D59, waterborne urethane clear and 2nd coat with Resene Poly-Satin D52, solventborne satin clear 4.22 INTERIOR PAPER FACED PLASTER/SOLID PLASTER/FIBROUS PLASTER For more information: Refer to Resene website Refer to http://www.resene.co.nz/archspec/datashts/spec15_Plaster_Interior.pdf Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne gloss System: Resene One-Line Spec. No. 15i 1.1 Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42; solventborne sealer For new wet areas - Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Enamacryl D309, waterborne gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Enamacryl D309, waterborne gloss enamel For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.11 Level 5 Use Resene One-Line Spec No. 15i 1.1 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.1 Level 4 Use Resene One-Line Spec No. 15i 1.1 Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne semi-gloss System: Resene One-Line Spec. No. 15i 1.2 Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer For new wet areas – Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lustacryl D310, waterborne semi-gloss enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lustacryl D310, waterborne semi-gloss enamel For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.21 Level 5 Use Resene One-Line Spec No. 15i 2.1 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.2 Level 4 Use Resene One-Line Spec No. 15i 1.2 Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne satin System: Resene One-Line Spec. No. 15i 1.3 Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Lumbersider D34, waterborne satin; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lumbersider D34, waterborne satin For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.31 Level 5 Use Resene One-Line Spec No. 15i 1.3 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.3 Level 4 Use Resene One-Line Spec No. 15i 1.3 Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne low sheen System: Resene One-Line Spec. No. 15i 1.4 ZS Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Zylone Sheen or Resene Zylone Sheen VOC Free D302, waterborne low sheen For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.41 ZS Level 5 Use Resene One-Line Spec No. 15i 1.4 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.4 ZS Level 4 Use Resene One-Line Spec No. 15i 1.4 ZS Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne low sheen System: Resene One-Line Spec. No. 15i 1.4 SC Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer For new wet areas – Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene SpaceCote Low Sheen D311, waterborne low sheen enamel For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.41 SC Level 5 Use Resene One-Line Spec No. 15i 1.41 SC Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.4 SC Level 4 Use Resene One-Line Spec No. 15i 1.4 SC Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne low sheen System: Resene One-Line Spec. No. 15i 1.4 K Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer; or For new wet areas – Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene SpaceCote Low Sheen Kitchen & Bathroom D311K, waterborne low sheen enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene SpaceCote Low Sheen Kitchen & Bathroom D311K, waterborne low sheen enamel For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.41 K Level 5 Use Resene One-Line Spec No. 15i 1.41 K Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.4 K Level 4 Use Resene One-Line Spec No. 15i 1.4 K Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne flat System: Resene One-Line Spec. No. 15i 1.5 Level 5 Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Zylone 20 D37, waterborne flat; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Zylone 20 D37, waterborne flat For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.51 Level 5 Use Resene One-Line Spec No. 15i 1.5 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.5 Level 4 Use Resene One-Line Spec No. 15i 1.5 Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne flat System: Resene One-Line Spec. No. 15i 1.5 Level 5 Ceiling Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery areas - Resene Sureseal D42, solventborne sealer 2nd coat: Resene Ceiling Paint D305, waterborne flat; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Ceiling Paint D305, waterborne flat For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.51 Level 5 Ceiling Use Resene One-Line Spec No. 15i 1.5 Level 5 Ceiling and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.5 Level 4 Ceiling Use Resene One-Line Spec No. 15i 1.5 Level 5 Ceiling and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer System: Resene One-Line Spec. No. 15i 1.5 SC Level 5 Description: Interior paperfaced plaster/solid plaster/fibrous plaster, waterborne flat Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat (if reqd): For wet, stained, porous or powdery area, Resene Sureseal D42, solventborne sealer; or For new wet area, Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene SpaceCote Flat D314, waterborne flat enamel; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene SpaceCote Flat D314, waterborne flat enamel For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.51 SC Level 5 Use Resene One-Line Spec No. 15i 1.5 SC Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 1.5 SC Level 4 Use Resene One-Line Spec No. 15i 1.5 SC Level 5 and for normal recommended system, remove Resene Broadwall Surface Prep & Seal from Surface prep and add 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer System: Resene One-Line Spec. No. 15i 2.1 Level 5 Description: Interior paperfaced plaster/solid plaster/fibrous plaster, solventborne gloss Surface prep: D84; D85; D87; Resene Broadwall Surface Prep & Seal D807, waterborne prep 1st coat: Resene Sureseal D42, solventborne sealer; or For new wet areas, Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Super Gloss D32, solventborne gloss For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 1.21 Level 5 Use Resene One-Line Spec No. 15i 2.1 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 2.1 Level 4, remove Resene Broadwall Surface Prep & Seal from Surface prep System: Resene One-Line Spec. No. 15i 2.2 Level 4 Description: Interior paperfaced plaster/solid plaster/fibrous plaster, solventborne semi-gloss Surface prep: D84; D85; D87 1st coat: Resene Sureseal D42, solventborne sealer; or For new wet area, Resene Waterborne Smooth Surface Sealer D47a, waterborne sealer 2nd coat: Resene Lusta-Glo D33, solventborne semi-gloss; or Resene Acrylic Undercoat D404, waterborne undercoat 3rd coat: Resene Lusta-Glo D33, solventborne semi-gloss For Level 5 Resene Broadwall 3 in 1 system - Resene One-Line Spec. No. 15i 2.21 Level 5 Use Resene One-Line Spec No. 15i 2.2 Level 5 and replace Resene Broadwall Surface Prep & Seal with Resene Broadwall 3 in 1 For Level 4 system – Resene One-Line Spec No. 15i 2.2 Level 4, remove Resene Broadwall Surface Prep & Seal from Surface prep 4.23 INTERIOR METALLIC FINISHES For more information: Refer to http://www.resene.co.nz/archspec/datashts/spec25_Special_Effects.pdf Description: Interior metallic finishes, waterborne metallic finish on Anaglypta, Scandatex, etc System: Resene One-Line Spec. No. 25i 1.3/5 Surface prep: D84; D85 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Enamacryl Metallic D309a, waterborne metallic 4th coat: Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional) Description: Interior metallic finishes, waterborne metallic finish on paperfaced plasterboard System: Resene One-Line Spec. No. 25i 1.3/51 Surface prep: D84; D85 1st coat: Resene Broadwall Waterborne Wallboard Sealer D403, waterborne sealer 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Enamacryl Metallic D309a, waterborne metallic 4th coat: Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional) Description: Interior metallic finishes, waterborne metallic finish on MDF joinery/doors System: Resene One-Line Spec. No. 25i 1.3/52 Surface prep: D82 1st coat: Resene Quick Dry D45, waterborne primer/undercoat 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Enamacryl Metallic D309a, waterborne metallic 4th coat: Resene Enamacryl Metallic D309a, waterborne metallic 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional) Description: Interior metallic finishes, waterborne pearlescent finish on interior surfaces System: Resene One-Line Spec. No. 25i 1.3/52 P Surface prep: D82 for MDF D84/D85 for paperfaced plasterboard 1st coat: Resene Quick Dry D45, waterborne primer/undercoat 2nd coat: Resene Lumbersider D34, waterborne satin 3rd coat: Resene Lumbersider D34, waterborne satin 4th coat: Resene Pearl Shimmer D312, waterborne pearlescent 5th coat: Resene Aquaclear D59, waterborne gloss urethane (optional) Description: Interior metallic finishes, solventborne metallic finish on concrete floor System: Resene One-Line Spec. No. 25i 2.3/5 Surface prep: D83 1st coat: Resene Armourcote 510 RA40, high solids epoxy 2nd coat: Resene Imperite I.F. 503 RA81, solventborne metallic 3rd coat: Resene Uracryl 400 Series Clear, solventborne clear Description: Interior metallic finishes, solventborne metallic finish on MDF joinery/doors System: Resene One-Line Spec. No. 25i 2.3/51 Surface prep: D82 1st coat: Refer Resene Paints Ltd 2nd coat: Resene Imperite I.F. 503 RA81, solventborne metallic 3rd coat: Resene Imperite I.F. 502 Clear RA82, semi-gloss clear 4.24 OTHER RESENE INTERIOR SYSTEMS ~ 6i INTERIOR FERROUS METALS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec6_Ferrous_Metals.pdf 7i INTERIOR NON-FERROUS METALS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec7_Non-Ferrous_Metals.pdf 9i INTERIOR TOTARA AND MATAI TIMBER ONLY Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec9_Matai_Totara.pdf 11i INTERIOR GLASS, GLAZED TILES, FORMICA, POLYETHYLENE, POLYPROPYLENE AND BAKED ENAMEL SYSTEMS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec11_Enamel_Glass_Tiles.pdf 12i INTERIOR GLASS REINFORCED POLYESTER, GLASS REINFORCED EPOXY, PVC, ACRYLIC SHEETING Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec12_Plastic_Materials.pdf 13i INTERIOR BRICK AND TERRACOTTA, CLEAR FINISHES Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec13_Brick_Terracotta.pdf 14i INTERIOR CLEAR FINISHES ON CLAY TILES, ABSORBENT TILES, STONE AND SLATE, DECORATIVE AGGREGATE FLOORING Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec14_Clay_Tiles_Stone.pdf 16i CANVAS, SCANDATEX AND HESSIAN Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec16_Canvas_Wallpaper.pdf 18i SPECIALIST FLOORING SYSTEMS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec18_Flooring_Specialist.pdf 19i ANTI GRAFFITI SYSTEMS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec19_Anti-Graffiti_System.pdf 20i TEXTURED COATINGS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec20_Textured_Coatings.pdf 21i PAINT EFFECTS Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec21_Paint_Effects.pdf 26i SPECIALIST INTERIOR FINISHES: RESENE ARMOURCAT ACID-CATALYSED Refer to Resene website http://www.resene.co.nz/archspec/datashts/spec26_Specialist_Acid_Cat.pdf © CIL MasterSpec® STANDARD 2007 6711R RESENE PAINTING Page 2 Branded specification review for 6711R_MASTERSPEC_STD.DOC Version date 2/09/2007 I have checked this specification thoroughly and have verified its content and technical accuracy. ? It is approved for issue ? It is approved for issue with changes as marked ? Signed:................................................................Date:....................................... © CIL MasterSpec® STANDARD 2007 6711R RESENE PAINTING Page 1