Garden bed frame

From NZ Gardener magazine

Perch this frame over a garden bed, and drape it with shade cloth, frost cloth or mesh, depending on the season, says Rose Hughes.

How to build a bed frame for your garden

This is for an 1100mm x 1450 high frame.

You will need:

  • 2 x 2.4m 100mm x 100mm laminated posts
  • 4.8m length of 250mm x 50mm treated pine
  • 4m of 22mm dowel
  • 45mm x 45mm x 1100mm timber offcut
  • Post top finial
  • 8g x 65mm & 8g x 100mm wood screws
  • Jig saw, drop saw, sander / sandpaper, Wood glue
  • Screwdriver, drill bit, countersink bit & 22mm paddle bit
  • Chisel, wood rasp & hammer
  • Clamps/ tape measure / pencil etc
  • Resene Woodsman Wood Oil Stain / paintbrush and turps.

Cost: $420 excluding stain.

Step 1 Step one
Cut the posts into 4 x 1000mm lengths. Create a template on card for the curved ribs. I used the full width of the 250mm wide timber and created as much curve as possible at one end with a flatter section at the other and approx. 65mm wide over 1m length of timber. Using the template cut out 4 x rails with the jigsaw. Sand well.
Step 2 Step two
Cut the 45mm square block to 110mm. Using clamps and spare timber for height (1300mm), work out the angle required to connect the ribs to the 45mm block and to the posts, approx. 40mm down from the top. The rib will be inset into the corner angle of the post by approx. 45mm. Mark all the angles on one rib and post. Cut the angles on each rib with the drop saw, sand well.
Step 3 Step three
Glue and screw the ribs to the 4 sides of the 45mm block, matching the top edge. Allow the glue to fully dry. Attach the finial with a suitable exterior glue and allow to dry.
Step 5 Step four
On the posts, mark 40mm and 115mm down from the top on one edge. Mark 55mm in from the outer edge. Set the drop saw blade to the correct angle so that the rib will inset at the correct angle. Cut multiple cuts carefully to the 55mm line. Use the chisel and hammer to cut an edge then remove the pieces and rasp the surface flat.
Step 6 Step five
Mark 160mm down from the top on the internal two faces of the posts. In the centre drill a 20mm deep hole with the paddle bit. Repeat for all four posts. Cut the dowel to 960mm lengths.
Step 7 Step six
Sand well and paint all the pieces. I used Resene Woodsman Wood Oil Stain in Shadowmatch. Dig the posts into the garden bed by approx. 100mm. Fit the dowels between the posts and attach the top. Screw the ribs into place from underneath back into the posts.

Resene Paints Ltd

Resene Paints Ltd   –

We would love to hear from you if you wish to use Resene's images, information and ideas for social medial, blogs, newsletters and other media use. Please email and let us know what you need, what it is for and how Resene will be acknowledged as the source of the content. We are happy to assist with most requests.

Our vision is to be respected as a trusted, ethical and sustainable company and acknowledged as the leading provider of innovative paint and colour technology. View Resene’s profile, Quality Policy, Environmental Policy and Health & Safety Policy.

Any personal data, such as name, address, phone, email details, supplied to Resene for the purposes of receiving newsletters, orders etc will be retained by Resene Paints Ltd and used only by Resene Paints Ltd and its trusted agencies for the purposes of communication/promotion/providing service to you. We do not sell, trade or otherwise transfer your personal data to outside third parties. If you wish to opt out of communication from Resene please complete our contact us form. View our full Privacy Policy.

Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online.   See measurements/conversions for more details on how electronic colour values are achieved.

View Videos