Feedback
Resene Paints - home page

Concrete planter


From NZ Gardener magazine

Rose Hughes’ modern, stylish planter is a great option to show off a statement plant.

Make a concrete planter

You will need:

  • 1 sheet 17mm ply
  • 1 sheet 7mm ply
  • 5.4m 18mm quad moulding
  • 8g x 50mm, 8g x 32mm screws
  • Small tacks
  • Dowel offcut 22mm diameter
  • Skil saw & straight edge
  • Wood glue, sand, silicone
  • Clamps, sandpaper, duct tape
  • Resene Concrete Primer
  • Resene Non-Skid Deck & Path
  • Paintbrushes

Cutting List:

  • From 17mm ply:
    • 2 x 610mm x 495mm
    • 2 x 610mm x 461mm
    • 1 x 810mm x 810mm
    • 4 x 300mm x 230mm
    • 4 cleats @ 50mm x 495mm
     
  • From 7mm ply:
    • 2 x 650mm x 360mm
    • 2 x 650mm x 375mm
    • 1 x 360mm x 360mm

Cost: $215 (excluding paint)

Step 1 Step one
Cut the pieces from the 17mm ply using the skil saw and a straight edge. For the moulding, cut 8 of each length adding 50mm. Add a 45-degree cut to all the pieces at one end, then move the saw to the opposite side and cut each piece to length.
Step 2Step two
Centre and glue each small panel to a large one. Nail in place once the glue is dry. Attach the mouldings with glue and small nails. Sand well when dry.
Step 3Step three
Join the edges of the form using the 50mm screws. Attach the dowel to the centre of the base. With the form centred on the base, place the cleats in position and secure these to the base using the 32mm screws. Use silicone to plug all the corners and joints.
Step 4 Step four
Cut out the inner former pieces, tape together using duct tape. Cover with plastic bag, securing with more duct tape.
Step 5Step five
Mix the concrete (following the instruction; with appropriate safety gear). Concrete the base up to the top of the drain dowel. Insert the former, centre it and trowel the concrete down the sides. You may need some wood offcuts to keep the inner former centred. Weight down the former with sand.
Step 6Step six
Allow to fully dry. Tip out the sand, peel out the former pieces. Unscrew the former and remove the ply. Unscrew the drain plug and remove the base. You may need to drill out the wooden dowel. Allow the concrete to fully cure. Paint with Resene Concrete primer and a topcoat of Non-Skid Deck & Path (I used Landscape Grey).
 

Resene Paints Ltd

Resene Paints Ltd   – www.resene.com

We would love to hear from you if you wish to use Resene's images, information and ideas for social medial, blogs, newsletters and other media use. Please email update@resene.co.nz and let us know what you need, what it is for and how Resene will be acknowledged as the source of the content. We are happy to assist with most requests.

Our vision is to be respected as a trusted, ethical and sustainable company and acknowledged as the leading provider of innovative paint and colour technology. View Resene’s profile, Quality Policy, Environmental Policy and Health & Safety Policy.

Any personal data, such as name, address, phone, email details, supplied to Resene for the purposes of receiving newsletters, orders etc will be retained by Resene Paints Ltd and used only by Resene Paints Ltd and its trusted agencies for the purposes of communication/promotion/providing service to you. We do not sell, trade or otherwise transfer your personal data to outside third parties. If you wish to opt out of communication from Resene please complete our contact us form. View our full Privacy Policy.

Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online.   See measurements/conversions for more details on how electronic colour values are achieved.

View Videos