DIY project categories...

Videos: DIY | habitat videos | Colour class

Tactile texture

Project ideas and inspiration from Good magazine

Welcome texture into your room by using leftover Resene Anaglypta wallpaper to accentuate furniture and décor items.

Re-covering a lampshade and cabinet door in wallpaper are simple ways to add visual interest to your bedroom. Although you could use any Resene wallpaper for this project, the best part with Resene Anaglypta wallpaper is that it can be re-painted should you wish to change your colour scheme in the future!

Accentuate furniture with Anaglypta wallpaper

Wall painted in Resene Rice Cake, conch shell painted in Resene Quarter Rice Cake, pot painted in Resene Liquid Gold. Bedding: Resene Living Adara duvet cover set in Botticelli and Resene Living Noora European pillowslip in Thumbs Up. Artwork made from Resene Wallpaper Collection ONB102696234.

What you'll need

Resene wallpaper offcut. I used Resene Wallpaper Collection Anaglypta RD567.
Resene testpots in the colours of your choice. I used Resene Half Escape, Resene Bismark, Resene Quarter Rice Cake and Resene Indian Ink.
Resene testpot brush
Ruler and pencil
Lamp to makeover
Scissors or craft knife
Double-sided tape
Bias binding for the top and bottom of the lamp
PVA glue
Painter’s tape

Additional materials for the cabinet:

ShurStik Green Granulated Size
Resene Enamacryl tinted to the colour of your choice. I used Resene Corn Field.

Step by step instructions

Tactile texture - Step 1 Step 1
Paint your wallpaper in your chosen Resene testpot colour. Allow to dry completely between coats. Measure the height and diameter of your lamp and add 2cm to the width measurement so that the ends overlap when wrapped around the lamp shade. Mark this measurement and cut out.

Tactile texture - Step 2 Step 2
On one end of the short ends of the wallpaper, attach double-sided tape to the wrong side and fold the paper over by 1cm.

Tactile texture - Step 3 Step 3
Run double-sided tape along the top and bottom of the wrong side of the wallpaper.

Tactile texture - Step 4 Step 4
Line the wallpaper up with the edges of the lampshade and overlap the ends, securing with double-sided tape.

Tactile texture - Step 5 Step 5
Attach double-sided tape to the top and bottom of the lampshade.

Tactile texture - Step 6 Step 6
Starting from the seam at the back of the lamp, wrap the bias binding around the top of the lampshade. Overlap the ends and secure using PVA glue.

Tactile texture - Step 7 Step 7
Apply PVA glue to the inside rim and fold the bias binding down. Secure with pegs until the glue has dried. Repeat on the other end.

Tactile texture - Step 8 Step 8
Once the glue is completely dry, run painter’s tape around the inside of the lampshade underneath the bias binding. Paint the entire piece of fabric in the same Resene colour as your lampshade. Get creative and paint the base in complementary colours.

Cabinet creativity

Cut the Resene wallpaper to the dimensions of your cabinet door or drawers. Remove any hardware such as handles or knobs. Mix the wallpaper size according to the packet directions and use a testpot brush to coat the cabinet door evenly with the size. Lay your wallpaper over the door and use a clean cloth to gently smooth it out to the sides and corners. Paint the entire piece of furniture in Resene Enamacryl in your choice of colour. Reattach hardware once the paint is dry.

Resene Quarter Rice Cake

Resene Liquid Gold

Project by Shani Luckman. Photography Amanda Reelick.

› Download this article as a PDF

August 2023

Good magazine projects
Wanting to tackle a project at your place but only have a weekend to spare? Get inspired with these projects from Good magazine. Reclaim and upcycle with paint.

View Good projects | View all projects

Resene Paints (Australia) Limited – www.resene.com