Resene primers, sealers and undercoats product range

Resene Acrylic Undercoat
general purpose undercoat - exterior/interior - waterborne
Eco Choice approved

Resene Acrylic Undercoat is an easy brushing, quick, hard drying undercoat with exceptional flow and sanding characteristics. While specifically designed for maximum benefit under waterborne enamels, such as Resene Enamacryl and Resene Lustacryl, Resene Acrylic Undercoat tinted to the correct colour is ideal for use under a wide range of waterborne and solventborne topcoats to improve the hiding of the paint system.

Resene Acrylic Undercoat gives all the hiding benefits associated with Resene Enamel Undercoat combined with the advantages of being waterborne, such as easy clean up in water, lower odour and therefore the desirability of using it with both acrylic and enamel topcoats. Suitable for interior and exterior use, it can be used in most paint systems as a substitute for Resene Enamel Undercoat.

For a consistent undercoat solution from solventborne to waterborne, Resene Enamel Undercoat and Resene Acrylic Undercoat, use a varishade colour system to provide the right basecoat for any shade. This helps provide the chosen topcoat with enhanced obliteration. Available in white and varishade tone there are six options including white and five varishades which grow steadily darker or higher in value moving from 1 to 5. White is tinted to the three palest shades while the varishade tone is tinted to reach the two deepest shades.

For optimum effect, CoolColour topcoats should use a white Resene Acrylic Undercoat or white primer only.

Choosing which varishade to use is recommended through the Resene e-tint colour formulation system. Bright accent colours such as bright reds, yellows and oranges tend to use a slightly lighter varishade than you may expect.

Typical uses: All exterior and interior prepared surfaces, block and brickwork, cement plasters, cloth and woven wallcoverings, fibre and particle board, furniture, paperfaced plasterboard (GIB®, Gyprock®), repaint old work, timber (including Matai, Spotted Gum and Totara), wallboards, wallpaper.

Resene Aluminium Wood Primer
aluminium wood primer – exterior - solventborne

Resene Aluminium Wood Primer is a lead and extender free primer based on mixed oil and oil-modified alkyds. Its sole pigmentation is aluminium flake.

Typical uses: Resene Aluminium Wood Primer may be used in any area in which conventional wood primers are used. Typically, however, it is used in more difficult areas where surface preparation cannot be of a high standard; knots exist in the timber; or staining is a major problem. While it is not offered as a cure-all, its performance in these areas is often much better than conventional primers.

Resene AquaLAQ NGR Alkyd Primer Sealer
solventborne interior

Resene AquaLAQ NGR Alkyd Primer Sealer is a fast drying, solventborne primer sealer for MDF and wood with excellent adhesion and built in water and impact resistance. It is low odour and designed to seal off MDF board with minimal grain raising.

An alternative to Resene AquaLAQ Quick Dry waterborne sealer when a faster production time is required.

Typical uses: MDF, wood, cabinets, wooden blinds, furniture. Usually used by professional spray applicators.

Recommended as part of the Resene AquaLAQ system – find out more about Resene AquaLAQ.

Resene AquaLAQ Quick Dry Sealer
waterborne interior
Eco Choice approved

Resene AquaLAQ Quick Dry Sealer is a unique waterborne sealer designed to seal off grain raising in MDF to provide a sound, flat, and high quality substrate ready to be topcoated. With minimal sanding required, you can enjoy lower labour costs. Enjoy low odour and low VOC with this product.

The clear sealer may also be used on timber and timber/paper veneers, which would normally be susceptible to moisture, to highlight their warmth and grain while providing a sealed substrate suitable for topcoating.

Typical uses: Primer/sealer for MDF board, various types of mass produced boards, most wood substrates. Usually used by professional spray applicators.

Recommended as part of the Resene AquaLAQ system – find out more about Resene AquaLAQ.

Resene Aquapel & Terracotta Sealer – waterborne
clear water repellent treatment for terracotta – exterior/interior - waterborne
Eco Choice approved

Adding colour to the great outdoors is easy with Resene Aquapel & Resene Terracotta Sealer. Designed for use on terracotta pots inside and out, Resene Terracotta Sealer is suitable for use over a wide range of terracotta surfaces, including terracotta statues and ornaments to ready them for topcoating.

Resene Aquapel & Terracotta Sealer seals the surface of the terracotta and imparts excellent waterbeading properties to deter water penetration so even if you wish to leave the terracotta in its original terracotta colouring, it will help keep it looking good for longer. It is also the ideal basecoat for overcoating with Resene decorative topcoats so you can add your own decorative flair in colour to terracotta pots, statues and ornaments.

This product has changed names from Resene Terracotta Sealer.

Typical uses: Most porous building materials, terracotta and as a protective finish over Resene FX Faux Rust Effect.

Resene Broadwall Waterborne Wallboard Sealer
waterborne wallboard sealer – interior - waterborne
Eco Choice approved

Resene Broadwall Waterborne Wallboard Sealer is a water reducible first coat for plasterboard walls and air-dry stoppings. Designed to minimise porosity and textural differences. No added VOCs.

Typical uses: Air-dry (polymer based) stoppings and finishing compounds, paperfaced plasterboard (GIB®, Gyprock®).

Resene Concrete Primer
concrete primer – exterior/interior - waterborne
Eco Choice approved

Resene Concrete Primer is designed for cementitious surfaces, including all concrete, plaster and surfaces, such as fibre cement to make ready for topcoating. Provides long-term adhesion coupled with exceptional durability even when left uncoated for prolonged periods.

Typical uses: Brick and blockwork, cementitious surfaces, fibre cement, formed concrete, plaster, precast panels, tilt slab.

Resene ConcreteSeal 3 in 1
fast drying concrete primer/sealer – exterior/interior - solventborne

Resene ConcreteSeal 3 in 1 is formulated to adhere well to concrete and be a fast drying versatile sealer/primer for interior concrete floors and exterior tilt slab. It's also ideal for garage and other residential and commercial floors being painted with Resene Walk-on. When used on properly prepared concrete floors, it will not flake off where hot car tyres stand. Properly prepared concrete needs to be clean from oil, grease, dirt and curing membranes.

It may also be used as coloured dust coat for new and aged interior concrete floors.

Often with tilt slab problems occur because of poor surface preparation and a failure to remove form oils and surface treatments before applying topcoats. Using Resene ConcreteSeal 3 in 1 helps the paint system adhere to the tilt slab allowing the topcoats to hold on better.

Typical uses: Concrete, concrete floors, dust coat for interior concrete floors, tilt slab.

Resene Enamel Undercoat
general purpose undercoat - exterior/interior - solventborne

Resene Enamel Undercoat is a blend of special alkyd resins balanced with unique pigments. An easy brushing, quick, hard drying undercoat with exceptional flow and sanding properties.

For a consistent undercoat solution from solventborne to waterborne, Resene Enamel Undercoat and Resene Acrylic Undercoat, use a varishade colour system to provide the right basecoat for any shade. This helps provide the chosen topcoat with enhanced obliteration. Available in white and varishade tone there are six options including white and five varishades which grow steadily darker or higher in value moving from 1 to 5. White is tinted to the three palest shades while the varishade tone is tinted to reach the two deepest shades.

For optimum effect, CoolColour topcoats should use a white Resene Acrylic Undercoat or white primer only.

Choosing which varishade to use is recommended through the Resene e-tint colour formulation system. Bright accent colours such as bright reds, yellows and oranges tend to use a slightly lighter varishade than you may expect.

Typical uses: All exterior and interior prepared surfaces, architraves, bathrooms, fibre and particle board, furniture, kitchens, laundries, paperfaced plasterboard (GIB®, Gyprock®), skirtings, suitably primed metals, timber doors, wallboards, weatherboards.

Resene Galvo One
galvanised steel primer - exterior - solventborne

Resene Galvo One is a single pack primer based on alkyd resins and special anti-corrosive pigments. Specially developed for direct application to new and weathered galvanised steel. Effectively welds itself to galvanised steel and stops zinc corrosion. Also suitable for use on Zincalume.

Typical uses: Downpipes, flashings, galvanised steel, gutters, long run and corrugated iron, roofs, zincalume.

Resene Galvo-Prime
galvanised steel primer - exterior - waterborne

Resene Galvo-Prime is a water reducible primer that matches its solvent reducible analogues even in marine exposures.

Typical uses: All exterior galvanised steel, non-ferrous metals, roofs, zincalume.

Resene GP Metal Primer
general purpose metal primer – exterior/interior - solventborne

Resene GP Metal Primer, is a general purpose (GP) primer based on a non saponifiable resin and a blend of anti-corrosive pigments designed for exterior and interior metals - steel, galvanised steel and Zincalume. It is ideal over sound metal surfaces and mild to moderately rusted surfaces - both red rust and zinc oxide – or white rust, which occurs on galvanised steel and zinc.

It's thick, which means you can get a lot of primer protection in just one coat, yet still easy to apply and use.

As with any metal finishing product, before you start priming, all salt and loose corrosion must be removed.

We also have a range of galvanised iron primers - Resene Galvo One and Resene Galvo-Prime - especially ideal for those planning roof painting projects to ensure the surface is properly primed before topcoating in Resene Summit Roof for a durable finish.

Typical uses: Aluminium, galvanising, repaints, steel, zincalume.

Resene HydraBlock
waterborne - epoxy barrier

Hydrostatic pressure can cause moisture to rise through the pores in concrete, damaging an impermeable film sitting on the surface, usually through blistering or pressure sufficient to blow sections of the coating off. Resene HydraBlock is a transparent two pack low VOC waterborne epoxy barrier coating for application to interior cementitious surfaces, such as masonry - walls, in-situ concrete - walls/floors and plastered walls, subject to hydrostatic pressure. Resene HydraBlock controls rising damp and efflorescence. It has excellent adhesion and is tolerant of application over damp surfaces.

Typical uses: Masonry – walls, in-situ concrete – walls/floors and plastered walls.

Resene Laminate and Melamine Primer (coming soon)
exterior/interior – waterborne

Resene Laminate and Melamine Primer is a waterborne 'adhesion primer' designed for use over a series of surfaces usually considered difficult to coat or in need of expensive pre-treatment. Fast drying, easy application and wide compatibility with Resene waterborne topcoats.

For old, varnished surfaces, use Resene Waterborne Sureseal.

Typical uses: As a pre-treatment on laminated surfaces, Formica®/Melteca®, melamine laminates and glazed tiles.

Resene Membrane Primer (previously known as Membrane Roofing Primer)
exterior/interior - waterborne
Eco Choice approved

Resene Membrane Primer is a specially formulated pre-treatment to upgrade adhesion, both wet and dry, to rubber membrane sheeting materials.

Typical uses: Asphalt tennis courts, bituminous substrates, EPDM and butyl rubber membrane sheeting.

Resene Pre-Coated Steel Primer
exterior - solventborne

Pre-coated coloured steel, such as ColorSteel®, ColorBond® and ColorCote, is a hugely popular option for roofs and may also be used as cladding. However inevitably owners want a colour change, sometimes within months of installation or sometimes years later. To make it easier to prepare the surface for topcoating, Resene has launched new Resene Pre-Coated Steel Primer. Resene Pre-Coated Steel Primer is a single pack adhesion primer for application to new factory coated roofing and cladding to ready it for topcoating with Resene waterborne paints. It can also be used as an anti-corrosive primer for new or weathered Zincalume and galvanising where a solventborne cool primer is required to maximise heat reflection when topcoating with Resene CoolColours.

Simply apply, allow to dry and you're ready to topcoat with Resene Summit Roof on roofs or you can opt for waterborne exterior finishes such as Resene Lumbersider waterborne low sheen, Resene Sonyx 101 waterborne semi-gloss or Resene Hi-Glo waterborne gloss on cladding.

Typical uses: Factory coated steel cladding/roofing such as COLORBOND®, COLORCOTE®, COLORSTEEL®, and other pre-coated steel, horizontal and vertical applications, including roofs, walls and fences.

Resene Quick Dry
waterborne primer undercoat - exterior/interior - waterborne
Eco Choice approved

Resene Quick Dry Waterborne Primer Undercoat provides long-term flexibility over unstable substrates coupled with exceptional durability even when left uncoated for prolonged periods. The latest formulation has enhanced flow and sanding characteristics for maximum benefit under waterborne enamels, such as Resene Enamacryl and Resene Lustacryl.

Typical uses: Architraves, block and brickwork, cement plaster, cloth and woven wallcoverings, particle board, repaint old work, timber (including Matai, Spotted Gum and Totara), wallboards, wallpaper.

Resene Quick Dry End Seal
waterborne sealer

When you're on the job site, the fiddly jobs can be annoying, such as making sure the ends of timber are properly sealed before the timber is erected. Resene Quick Dry End Seal is a modified version of Resene Quick Dry in a unique bottle with built in brush applicator, which can be used to quickly and easily coat the ends of timber without the hassle of getting out a can of primer and a paintbrush and then having to wash it up afterwards. It's quick and easy to use; simply open the lid and brush the Resene Quick Dry End Seal onto the surface of the timber using the applicator.

Resene Sureseal
penetrating pigmented sealer - exterior/interior - solventborne

Resene Sureseal is a pigmented, solventborne, alkali-resistant, penetrating sealer with the ability to penetrate and bond old decaying surfaces and make them suitable for painting. This lower odour formulation acts as a surface conditioner that also reduces bleeding of water stains and dries without the unwanted and strong solvent odours associated with traditional solventborne products.

Typical uses: Brickwork, chalky and powdery surfaces, concrete tiles, fibre cement, fibrous plaster, paperfaced plasterboard (GIB®, Gyprock®), plaster – gypsum and solid, plaster glass, stucco, timber.

Resene Waterborne Smooth Surface Sealer
adhesion primer - exterior/interior - waterborne

Resene Waterborne Smooth Surface Sealer has been tailored to be a waterborne 'adhesive primer' over a series of surfaces usually considered difficult to coat or in need of expensive pre-treatment. Fast drying, easy application and wide compatibility with topcoats are added features of this product.

Typical uses: As a pre-treatment on aluminium, baked enamels, copper and its alloys, glass and ceramics, laminated surfaces, melamine, most glazed surfaces, old varnished surfaces.

Note: This product is being replaced by Resene Laminate and Melamine Primer.

Resene Waterborne Sureseal - pigmented sealer
penetrating pigmented sealer - interior - waterborne

Resene Waterborne Sureseal is a pigmented penetrating sealer designed to ready a wide range of interior surfaces ready for topcoating, including old varnishes and Lockwood® finishes. It has excellent adhesion, reduces bleeding of water stains, low VOCs and dries without the unwanted and strong solvent odours associated with traditional solventborne products. Suitable for use in broadwall areas through to wet areas like bathrooms and kitchens. Resene Waterborne Sureseal is a penetrating sealer and should not be regarded as forming part of the film build of the subsequent coating.

Typical uses: Interior surfaces including baked enamels, glass/ceramics, fibre cement, glazed surfaces, plasterboard and gypsum stoppings, solid plaster, tiles, varnished surfaces and to seal plasterboard prior to wallpapering.

Resene Waterborne Vinyl Wallpaper Sealer
vinyl wallpaper sealer – interior - waterborne

Those familiar with painting over wallpaper will shudder at the mention of plasticiser. Painting directly over vinyl wallpaper can cause the plasticiser hidden in the vinyl wallpaper to migrate through to the topcoats affecting the cure of the coating and leaving a sticky surface.

To alleviate this problem many simply removed the wallpaper, expending much time and energy in the process, before coating the surface in paint. While this resolves the sticky surface issue, it is a resource intensive option and not for the fainthearted.

Recognising the need for a quick and easy method of coating vinyl wallpaper, Resene Waterborne Vinyl Wallpaper Sealer is designed to be applied direct to the vinyl wallpaper, sealing in the plasticiser leaving the surface ready for finishing with the desired topcoats.

Those wishing to take advantage of the texture of the existing wallpaper can safely seal the vinyl wallpaper with Resene Waterborne Vinyl Wallpaper Sealer and follow this in the desired topcoats leaving a freshly coated surface with the texture of the original wallpaper.

Typical uses: Wallpaper.

Resene Waterborne Vinyl Wallpaper Sealer is a waterborne and lower odour replacement of the older solventborne Resene Vinyl Wallpaper Sealer. The older solventborne product has now been deleted.

Resene Wood Primer
general purpose wood primer - exterior - solventborne

Resene Wood Primer is based on an oil-modified alkyd resin blended with pigments to give ease of application and good penetration to substrates. Flexible and produces the ideal surface for subsequent paint finishes.

Typical uses: Doors, outdoor furniture, timber, weatherboards, window frames.